Home Articles FAQs XREF Games Software Instant Books BBS About FOLDOC RFCs Feedback Sitemap
irt.Org

Request For Comments - RFC7787

You are here: irt.org | RFCs | RFC7787 [ previous next ]






Internet Engineering Task Force (IETF)                       M. Stenberg
Request for Comments: 7787                                      S. Barth
Category: Standards Track                                    Independent
ISSN: 2070-1721                                               April 2016


                  Distributed Node Consensus Protocol

Abstract

   This document describes the Distributed Node Consensus Protocol
   (DNCP), a generic state synchronization protocol that uses the
   Trickle algorithm and hash trees.  DNCP is an abstract protocol and
   must be combined with a specific profile to make a complete
   implementable protocol.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc7787.

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.







Stenberg & Barth             Standards Track                    [Page 1]



RFC 7787           Distributed Node Consensus Protocol        April 2016


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Applicability . . . . . . . . . . . . . . . . . . . . . .   4
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   6
     2.1.  Requirements Language . . . . . . . . . . . . . . . . . .   8
   3.  Overview  . . . . . . . . . . . . . . . . . . . . . . . . . .   8
   4.  Operation . . . . . . . . . . . . . . . . . . . . . . . . . .   9
     4.1.  Hash Tree . . . . . . . . . . . . . . . . . . . . . . . .   9
       4.1.1.  Calculating Network State and Node Data Hashes  . . .  10
       4.1.2.  Updating Network State and Node Data Hashes . . . . .  10
     4.2.  Data Transport  . . . . . . . . . . . . . . . . . . . . .  10
     4.3.  Trickle-Driven Status Updates . . . . . . . . . . . . . .  12
     4.4.  Processing of Received TLVs . . . . . . . . . . . . . . .  13
     4.5.  Discovering, Adding, and Removing Peers . . . . . . . . .  15
     4.6.  Data Liveliness Validation  . . . . . . . . . . . . . . .  16
   5.  Data Model  . . . . . . . . . . . . . . . . . . . . . . . . .  17
   6.  Optional Extensions . . . . . . . . . . . . . . . . . . . . .  19
     6.1.  Keep-Alives . . . . . . . . . . . . . . . . . . . . . . .  19
       6.1.1.  Data Model Additions  . . . . . . . . . . . . . . . .  20
       6.1.2.  Per-Endpoint Periodic Keep-Alives . . . . . . . . . .  20
       6.1.3.  Per-Peer Periodic Keep-Alives . . . . . . . . . . . .  20
       6.1.4.  Received TLV Processing Additions . . . . . . . . . .  21
       6.1.5.  Peer Removal  . . . . . . . . . . . . . . . . . . . .  21
     6.2.  Support for Dense Multicast-Enabled Links . . . . . . . .  21
   7.  Type-Length-Value Objects . . . . . . . . . . . . . . . . . .  22
     7.1.  Request TLVs  . . . . . . . . . . . . . . . . . . . . . .  23
       7.1.1.  Request Network State TLV . . . . . . . . . . . . . .  23
       7.1.2.  Request Node State TLV  . . . . . . . . . . . . . . .  24
     7.2.  Data TLVs . . . . . . . . . . . . . . . . . . . . . . . .  24
       7.2.1.  Node Endpoint TLV . . . . . . . . . . . . . . . . . .  24
       7.2.2.  Network State TLV . . . . . . . . . . . . . . . . . .  25
       7.2.3.  Node State TLV  . . . . . . . . . . . . . . . . . . .  25
     7.3.  Data TLVs within Node State TLV . . . . . . . . . . . . .  26
       7.3.1.  Peer TLV  . . . . . . . . . . . . . . . . . . . . . .  26
       7.3.2.  Keep-Alive Interval TLV . . . . . . . . . . . . . . .  27
   8.  Security and Trust Management . . . . . . . . . . . . . . . .  27
     8.1.  Trust Method Based on Pre-Shared Key  . . . . . . . . . .  27
     8.2.  PKI-Based Trust Method  . . . . . . . . . . . . . . . . .  28
     8.3.  Certificate-Based Trust Consensus Method  . . . . . . . .  28
       8.3.1.  Trust Verdicts  . . . . . . . . . . . . . . . . . . .  28
       8.3.2.  Trust Cache . . . . . . . . . . . . . . . . . . . . .  29
       8.3.3.  Announcement of Verdicts  . . . . . . . . . . . . . .  30
       8.3.4.  Bootstrap Ceremonies  . . . . . . . . . . . . . . . .  31
   9.  DNCP Profile-Specific Definitions . . . . . . . . . . . . . .  32
   10. Security Considerations . . . . . . . . . . . . . . . . . . .  34
   11. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  35




Stenberg & Barth             Standards Track                    [Page 2]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   12. References  . . . . . . . . . . . . . . . . . . . . . . . . .  36
     12.1.  Normative References . . . . . . . . . . . . . . . . . .  36
     12.2.  Informative References . . . . . . . . . . . . . . . . .  36
   Appendix A.  Alternative Modes of Operation . . . . . . . . . . .  38
     A.1.  Read-Only Operation . . . . . . . . . . . . . . . . . . .  38
     A.2.  Forwarding Operation  . . . . . . . . . . . . . . . . . .  38
   Appendix B.  DNCP Profile Additional Guidance . . . . . . . . . .  38
     B.1.  Unicast Transport -- UDP or TCP?  . . . . . . . . . . . .  38
     B.2.  (Optional) Multicast Transport  . . . . . . . . . . . . .  39
     B.3.  (Optional) Transport Security . . . . . . . . . . . . . .  39
   Appendix C.  Example Profile  . . . . . . . . . . . . . . . . . .  40
   Acknowledgements  . . . . . . . . . . . . . . . . . . . . . . . .  41
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  41

1.  Introduction

   DNCP is designed to provide a way for each participating node to
   publish a small set of TLV (Type-Length-Value) tuples (at most 64 KB)
   and to provide a shared and common view about the data published by
   every currently bidirectionally reachable DNCP node in a network.

   For state synchronization, a hash tree is used.  It is formed by
   first calculating a hash for the data set published by each node,
   called node data, and then calculating another hash over those node
   data hashes.  The single resulting hash, called network state hash,
   is transmitted using the Trickle algorithm [RFC6206] to ensure that
   all nodes share the same view of the current state of the published
   data within the network.  The use of Trickle with only short network
   state hashes sent infrequently (in steady state, once the maximum
   Trickle interval per link or unicast connection has been reached)
   makes DNCP very thrifty when updates happen rarely.

   For maintaining liveliness of the topology and the data within it, a
   combination of Trickled network state, keep-alives, and "other" means
   of ensuring reachability are used.  The core idea is that if every
   node ensures its peers are present, transitively, the whole network
   state also stays up to date.














Stenberg & Barth             Standards Track                    [Page 3]



RFC 7787           Distributed Node Consensus Protocol        April 2016


1.1.  Applicability

   DNCP is useful for cases like autonomous bootstrapping, discovery,
   and negotiation of embedded network devices like routers.
   Furthermore, it can be used as a basis to run distributed algorithms
   like [RFC7596] or use cases as described in Appendix C.  DNCP is
   abstract, which allows it to be tuned to a variety of applications by
   defining profiles.  These profiles include choices of:

   -  unicast transport:  a datagram or stream-oriented protocol (e.g.,
      TCP, UDP, or the Stream Control Transmission Protocol (SCTP)) for
      generic protocol operation.

   -  optional transport security:  whether and when to use security
      based on Transport Layer Security (TLS) or Datagram Transport
      Layer Security (DTLS), if supported over the chosen transport.

   -  optional multicast transport:  a multicast-capable protocol like
      UDP allowing autonomous peer discovery or more efficient use of
      multiple access links.

   -  communication scopes:  using either hop by hop only relying on
      link-local addressing (e.g., for LANs), addresses with broader
      scopes (e.g., over WANs or the Internet) relying on an existing
      routing infrastructure, or a combination of both (e.g., to
      exchange state between multiple LANs over a WAN or the Internet).

   -  payloads:  additional specific payloads (e.g., IANA standardized,
      enterprise-specific, or private use).

   -  extensions:  possible protocol extensions, either as predefined in
      this document or specific for a particular use case.

   However, there are certain cases where the protocol as defined in
   this document is a less suitable choice.  This list provides an
   overview while the following paragraphs provide more detailed
   guidance on the individual matters.

   -  large amounts of data:  nodes are limited to 64 KB of published
      data.

   -  very dense unicast-only networks:  nodes include information about
      all immediate neighbors as part of their published data.

   -  predominantly minimal data changes:  node data is always
      transported as is, leading to a relatively large transmission
      overhead for changes affecting only a small part of it.




Stenberg & Barth             Standards Track                    [Page 4]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   -  frequently changing data:  DNCP with its use of Trickle is
      optimized for the steady state and less efficient otherwise.

   -  large amounts of very constrained nodes:  DNCP requires each node
      to store the entirety of the data published by all nodes.

   The topology of the devices is not limited and automatically
   discovered.  When relying on link-local communication exclusively,
   all links having DNCP nodes need to be at least transitively
   connected by routers running the protocol on multiple endpoints in
   order to form a connected network.  However, there is no requirement
   for every device in a physical network to run the protocol.
   Especially if globally scoped addresses are used, DNCP peers do not
   need to be on the same or even neighboring physical links.
   Autonomous discovery features are usually used in local network
   scenarios; however, with security enabled, DNCP can also be used over
   unsecured public networks.  Network size is restricted merely by the
   capabilities of the devices, i.e., each DNCP node needs to be able to
   store the entirety of the data published by all nodes.  The data
   associated with each individual node identifier is limited to about
   64 KB in this document; however, protocol extensions could be defined
   to mitigate this or other protocol limitations if the need arises.

   DNCP is most suitable for data that changes only infrequently to gain
   the maximum benefit from using Trickle.  As the network of nodes
   grows, or the frequency of data changes per node increases, Trickle
   is eventually used less and less, and the benefit of using DNCP
   diminishes.  In these cases, Trickle just provides extra complexity
   within the specification and little added value.

   The suitability of DNCP for a particular application can be roughly
   evaluated by considering the expected average network-wide state
   change interval A_NC_I; it is computed by dividing the mean interval
   at which a node originates a new TLV set by the number of
   participating nodes.  If keep-alives are used, A_NC_I is the minimum
   of the computed A_NC_I and the keep-alive interval.  If A_NC_I is
   less than the (application-specific) Trickle minimum interval, DNCP
   is most likely unsuitable for the application as Trickle will not be
   utilized most of the time.

   If constant rapid state changes are needed, the preferable choice is
   to use an additional point-to-point channel whose address or locator
   is published using DNCP.  Nevertheless, if doing so does not raise
   A_NC_I above the (sensibly chosen) Trickle interval parameters for a
   particular application, using DNCP is probably not suitable for the
   application.





Stenberg & Barth             Standards Track                    [Page 5]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   Another consideration is the size of the published TLV set by a node
   compared to the size of deltas in the TLV set.  If the TLV set
   published by a node is very large, and has frequent small changes,
   DNCP as currently specified in this specification may be unsuitable
   as it lacks a delta synchronization scheme to keep implementation
   simple.

   DNCP can be used in networks where only unicast transport is
   available.  While DNCP uses the least amount of bandwidth when
   multicast is utilized, even in pure unicast mode, the use of Trickle
   (ideally with k < 2) results in a protocol with an exponential
   backoff timer and fewer transmissions than a simpler protocol not
   using Trickle.

2.  Terminology

   DNCP profile      the values for the set of parameters given in
                     Section 9.  They are prefixed with DNCP_ in this
                     document.  The profile also specifies the set of
                     optional DNCP extensions to be used.  For a simple
                     example DNCP profile, see Appendix C.

   DNCP-based        a protocol that provides a DNCP profile, according
   protocol          to Section 9, and zero or more TLV assignments from
                     the per-DNCP profile TLV registry as well as their
                     processing rules.

   DNCP node         a single node that runs a DNCP-based protocol.

   Link              a link-layer media over which directly connected
                     nodes can communicate.

   DNCP network      a set of DNCP nodes running a DNCP-based
                     protocol(s) with a matching DNCP profile(s).  The
                     set consists of nodes that have discovered each
                     other using the transport method defined in the
                     DNCP profile, via multicast on local links, and/or
                     by using unicast communication.

   Node identifier   an opaque fixed-length identifier consisting of
                     DNCP_NODE_IDENTIFIER_LENGTH bytes that uniquely
                     identifies a DNCP node within a DNCP network.

   Interface         a node's attachment to a particular link.

   Address           an identifier used as the source or destination of
                     a DNCP message flow, e.g., a tuple (IPv6 address,
                     UDP port) for an IPv6 UDP transport.



Stenberg & Barth             Standards Track                    [Page 6]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   Endpoint          a locally configured termination point for
                     (potential or established) DNCP message flows.  An
                     endpoint is the source and destination for separate
                     unicast message flows to individual nodes and
                     optionally for multicast messages to all thereby
                     reachable nodes (e.g., for node discovery).
                     Endpoints are usually in one of the transport modes
                     specified in Section 4.2.

   Endpoint          a 32-bit opaque and locally unique value, which
   identifier        identifies a particular endpoint of a particular
                     DNCP node.  The value 0 is reserved for DNCP and
                     DNCP-based protocol purposes and not used to
                     identify an actual endpoint.  This definition is in
                     sync with the interface index definition in
                     [RFC3493], as the non-zero small positive integers
                     should comfortably fit within 32 bits.

   Peer              another DNCP node with which a DNCP node
                     communicates using at least one particular local
                     and remote endpoint pair.

   Node data         a set of TLVs published and owned by a node in the
                     DNCP network.  Other nodes pass it along as is,
                     even if they cannot fully interpret it.

   Origination time  the (estimated) time when the node data set with
                     the current sequence number was published.

   Node state        a set of metadata attributes for node data.  It
                     includes a sequence number for versioning, a hash
                     value for comparing equality of stored node data,
                     and a timestamp indicating the time passed since
                     its last publication (i.e., since the origination
                     time).  The hash function and the length of the
                     hash value are defined in the DNCP profile.

   Network state     a hash value that represents the current state of
   hash              the network.  The hash function and the length of
                     the hash value are defined in the DNCP profile.
                     Whenever a node is added, removed, or updates its
                     published node data, this hash value changes as
                     well.  For calculation, please see Section 4.1.

   Trust verdict     a statement about the trustworthiness of a
                     certificate announced by a node participating in
                     the certificate-based trust consensus mechanism.




Stenberg & Barth             Standards Track                    [Page 7]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   Effective trust   the trust verdict with the highest priority within
   verdict           the set of trust verdicts announced for the
                     certificate in the DNCP network.

   Topology graph    the undirected graph of DNCP nodes produced by
                     retaining only bidirectional peer relationships
                     between nodes.

   Bidirectionally   a peer is locally unidirectionally reachable if a
   reachable         consistent multicast or any unicast DNCP message
                     has been received by the local node (see Section
                     4.5).  If said peer in return also considers the
                     local node unidirectionally reachable, then
                     bidirectionally reachability is established.  As
                     this process is based on publishing peer
                     relationships and evaluating the resulting topology
                     graph as described in Section 4.6, this information
                     is available to the whole DNCP network.

   Trickle instance  a distinct Trickle [RFC6206] algorithm state kept
                     by a node (Section 5) and related to an endpoint or
                     a particular (peer, endpoint) tuple with Trickle
                     variables I, t, and c.  See Section 4.3.

2.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in RFC
   2119 [RFC2119].

3.  Overview

   DNCP operates primarily using unicast exchanges between nodes, and it
   may use multicast for Trickle-based shared state dissemination and
   topology discovery.  If used in pure unicast mode with unreliable
   transport, Trickle is also used between peers.

   DNCP is based on exchanging TLVs (Section 7) and defines a set of
   mandatory and optional ones for its operation.  They are categorized
   into TLVs for requesting information (Section 7.1), transmitting data
   (Section 7.2), and being published as data (Section 7.3).  DNCP-based
   protocols usually specify additional ones to extend the capabilities.

   DNCP discovers the topology of the nodes in the DNCP network and
   maintains the liveliness of published node data by ensuring that the
   publishing node is bidirectionally reachable.  New potential peers
   can be discovered autonomously on multicast-enabled links; their



Stenberg & Barth             Standards Track                    [Page 8]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   addresses may be manually configured or they may be found by some
   other means defined in the particular DNCP profile.  The DNCP profile
   may specify, for example, a well-known anycast address or provision
   the remote address to contact via some other protocol such as DHCPv6
   [RFC3315].

   A hash tree of height 1, rooted in itself, is maintained by each node
   to represent the state of all currently reachable nodes (see
   Section 4.1), and the Trickle algorithm is used to trigger
   synchronization (see Section 4.3).  The need to check peer nodes for
   state changes is thereby determined by comparing the current root of
   their respective hash trees, i.e., their individually calculated
   network state hashes.

   Before joining a DNCP network, a node starts with a hash tree that
   has only one leaf if the node publishes some TLVs, and no leaves
   otherwise.  It then announces the network state hash calculated from
   the hash tree by means of the Trickle algorithm on all its configured
   endpoints.

   When an update is detected by a node (e.g., by receiving a different
   network state hash from a peer), the originator of the event is
   requested to provide a list of the state of all nodes, i.e., all the
   information it uses to calculate its own hash tree.  The node uses
   the list to determine whether its own information is outdated and --
   if necessary -- requests the actual node data that has changed.

   Whenever a node's local copy of any node data and its hash tree are
   updated (e.g., due to its own or another node's node state changing
   or due to a peer being added or removed), its Trickle instances are
   reset, which eventually causes any update to be propagated to all of
   its peers.

4.  Operation

4.1.  Hash Tree

   Each DNCP node maintains an arbitrary width hash tree of height 1.
   The root of the tree represents the overall network state hash and is
   used to determine whether the view of the network of two or more
   nodes is consistent and shared.  Each leaf represents one
   bidirectionally reachable DNCP node.  Every time a node is added or
   removed from the topology graph (Section 4.6), it is likewise added
   or removed as a leaf.  At any time, the leaves of the tree are
   ordered in ascending order of the node identifiers of the nodes they
   represent.





Stenberg & Barth             Standards Track                    [Page 9]



RFC 7787           Distributed Node Consensus Protocol        April 2016


4.1.1.  Calculating Network State and Node Data Hashes

   The network state hash and the node data hashes are calculated using
   the hash function defined in the DNCP profile (Section 9) and
   truncated to the number of bits specified therein.

   Individual node data hashes are calculated by applying the function
   and truncation on the respective node's node data as published in the
   Node State TLV.  Such node data sets are always ordered as defined in
   Section 7.2.3.

   The network state hash is calculated by applying the function and
   truncation on the concatenated network state.  This state is formed
   by first concatenating each node's sequence number (in network byte
   order) with its node data hash to form a per-node datum for each
   node.  These per-node data are then concatenated in ascending order
   of the respective node's node identifier, i.e., in the order that the
   nodes appear in the hash tree.

4.1.2.  Updating Network State and Node Data Hashes

   The network state hash and the node data hashes are updated on-demand
   and whenever any locally stored per-node state changes.  This
   includes local unidirectional reachability encoded in the published
   Peer TLVs (Section 7.3.1) and -- when combined with remote data --
   results in awareness of bidirectional reachability changes.

4.2.  Data Transport

   DNCP has few requirements for the underlying transport; it requires
   some way of transmitting either a unicast datagram or stream data to
   a peer and, if used in multicast mode, a way of sending multicast
   datagrams.  As multicast is used only to identify potential new DNCP
   nodes and to send status messages that merely notify that a unicast
   exchange should be triggered, the multicast transport does not have
   to be secured.  If unicast security is desired and one of the
   built-in security methods is to be used, support for some TLS-derived
   transport scheme -- such as TLS [RFC5246] on top of TCP or DTLS
   [RFC6347] on top of UDP -- is also required.  They provide for
   integrity protection and confidentiality of the node data, as well as
   authentication and authorization using the schemes defined in
   "Security and Trust Management" (Section 8).  A specific definition
   of the transport(s) in use and its parameters MUST be provided by the
   DNCP profile.

   TLVs (Section 7) are sent across the transport as is, and they SHOULD
   be sent together where, e.g., MTU considerations do not recommend
   sending them in multiple batches.  DNCP does not fragment or



Stenberg & Barth             Standards Track                   [Page 10]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   reassemble TLVs; thus, it MUST be ensured that the underlying
   transport performs these operations should they be necessary.  If
   this document indicates sending one or more TLVs, then the sending
   node does not need to keep track of the packets sent after handing
   them over to the respective transport, i.e., reliable DNCP operation
   is ensured merely by the explicitly defined timers and state machines
   such as Trickle (Section 4.3).  TLVs in general are handled
   individually and statelessly (and thus do not need to be sent in any
   particular order) with one exception: To form bidirectional peer
   relationships, DNCP requires identification of the endpoints used for
   communication.  As bidirectional peer relationships are required for
   validating liveliness of published node data as described in
   Section 4.6, a DNCP node MUST send a Node Endpoint TLV
   (Section 7.2.1).  When it is sent varies, depending on the underlying
   transport, but conceptually it should be available whenever
   processing a Network State TLV:

   o  If using a stream transport, the TLV MUST be sent at least once
      per connection but SHOULD NOT be sent more than once.

   o  If using a datagram transport, it MUST be included in every
      datagram that also contains a Network State TLV (Section 7.2.2)
      and MUST be located before any such TLV.  It SHOULD also be
      included in any other datagram to speed up initial peer detection.

   Given the assorted transport options as well as potential endpoint
   configuration, a DNCP endpoint may be used in various transport
   modes:

   Unicast:

      *  If only reliable unicast transport is used, Trickle is not used
         at all.  Whenever the locally calculated network state hash
         changes, a single Network State TLV (Section 7.2.2) is sent to
         every unicast peer.  Additionally, recently changed Node State
         TLVs (Section 7.2.3) MAY be included.

      *  If only unreliable unicast transport is used, Trickle state is
         kept per peer, and it is used to send Network State TLVs
         intermittently, as specified in Section 4.3.

   Multicast+Unicast:  If multicast datagram transport is available on
      an endpoint, Trickle state is only maintained for the endpoint as
      a whole.  It is used to send Network State TLVs periodically, as
      specified in Section 4.3.  Additionally, per-endpoint keep-alives
      MAY be defined in the DNCP profile, as specified in Section 6.1.2.





Stenberg & Barth             Standards Track                   [Page 11]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   MulticastListen+Unicast:  Just like unicast, except multicast
      transmissions are listened to in order to detect changes of the
      highest node identifier.  This mode is used only if the DNCP
      profile supports dense multicast-enabled link optimization
      (Section 6.2).

4.3.  Trickle-Driven Status Updates

   The Trickle algorithm [RFC6206] is used to ensure protocol
   reliability over unreliable multicast or unicast transports.  For
   reliable unicast transports, its actual algorithm is unnecessary and
   omitted (Section 4.2).  DNCP maintains multiple Trickle states as
   defined in Section 5.  Each such state can be based on different
   parameters (see below) and is responsible for ensuring that a
   specific peer or all peers on the respective endpoint are regularly
   provided with the node's current locally calculated network state
   hash for state comparison, i.e., to detect potential divergence in
   the perceived network state.

   Trickle defines 3 parameters: Imin, Imax, and k.  Imin and Imax
   represent the minimum value for I and the maximum number of doublings
   of Imin, where I is the time interval during which at least k Trickle
   updates must be seen on an endpoint to prevent local state
   transmission.  The actual suggested Trickle algorithm parameters are
   DNCP profile specific, as described in Section 9.

   The Trickle state for all Trickle instances defined in Section 5 is
   considered inconsistent and reset if and only if the locally
   calculated network state hash changes.  This occurs either due to a
   change in the local node's own node data or due to the receipt of
   more recent data from another node as explained in Section 4.1.  A
   node MUST NOT reset its Trickle state merely based on receiving a
   Network State TLV (Section 7.2.2) with a network state hash that is
   different from its locally calculated one.

   Every time a particular Trickle instance indicates that an update
   should be sent, the node MUST send a Network State TLV
   (Section 7.2.2) if and only if:

   o  the endpoint is in Multicast+Unicast transport mode, in which case
      the TLV MUST be sent over multicast.

   o  the endpoint is NOT in Multicast+Unicast transport mode, and the
      unicast transport is unreliable, in which case the TLV MUST be
      sent over unicast.






Stenberg & Barth             Standards Track                   [Page 12]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   A (sub)set of all Node State TLVs (Section 7.2.3) MAY also be
   included, unless it is defined as undesirable for some reason by the
   DNCP profile or to avoid exposure of the node state TLVs by
   transmitting them within insecure multicast when using secure
   unicast.

4.4.  Processing of Received TLVs

   This section describes how received TLVs are processed.  The DNCP
   profile may specify when to ignore particular TLVs, e.g., to modify
   security properties -- see Section 9 for what may be safely defined
   to be ignored in a profile.  Any 'reply' mentioned in the steps below
   denotes the sending of the specified TLV(s) to the originator of the
   TLV being processed.  All such replies MUST be sent using unicast.
   If the TLV being replied to was received via multicast and it was
   sent to a multiple access link, the reply MUST be delayed by a random
   time span in [0, Imin/2], to avoid potential simultaneous replies
   that may cause problems on some links, unless specified differently
   in the DNCP profile.  The sending of replies MAY also be rate limited
   or omitted for a short period of time by an implementation.  However,
   if the TLV is not forbidden by the DNCP profile, an implementation
   MUST reply to retransmissions of the TLV with a non-zero probability
   to avoid starvation, which would break the state synchronization.

   A DNCP node MUST process TLVs received from any valid (e.g.,
   correctly scoped) address, as specified by the DNCP profile and the
   configuration of a particular endpoint, whether this address is known
   to be the address of a peer or not.  This provision satisfies the
   needs of monitoring or other host software that needs to discover the
   DNCP topology without adding to the state in the network.

   Upon receipt of:

   o  Request Network State TLV (Section 7.1.1): The receiver MUST reply
      with a Network State TLV (Section 7.2.2) and a Node State TLV
      (Section 7.2.3) for each node data used to calculate the network
      state hash.  The Node State TLVs SHOULD NOT contain the optional
      node data part to avoid redundant transmission of node data,
      unless explicitly specified in the DNCP profile.

   o  Request Node State TLV (Section 7.1.2): If the receiver has node
      data for the corresponding node, it MUST reply with a Node State
      TLV (Section 7.2.3) for the corresponding node.  The optional node
      data part MUST be included in the TLV.

   o  Network State TLV (Section 7.2.2): If the network state hash
      differs from the locally calculated network state hash, and the
      receiver is unaware of any particular node state differences with



Stenberg & Barth             Standards Track                   [Page 13]



RFC 7787           Distributed Node Consensus Protocol        April 2016


      the sender, the receiver MUST reply with a Request Network State
      TLV (Section 7.1.1).  These replies MUST be rate limited to only
      at most one reply per link per unique network state hash within
      Imin.  The simplest way to ensure this rate limit is a timestamp
      indicating requests and sending at most one Request Network State
      TLV (Section 7.1.1) per Imin.  To facilitate faster state
      synchronization, if a Request Network State TLV is sent in a
      reply, a local, current Network State TLV MAY also be sent.

   o  Node State TLV (Section 7.2.3):

      *  If the node identifier matches the local node identifier and
         the TLV has a greater sequence number than its current local
         value, or the same sequence number and a different hash, the
         node SHOULD republish its own node data with a sequence number
         significantly greater than the received one (e.g., 1000) to
         reclaim the node identifier.  This difference is needed in
         order to ensure that it is higher than any potentially
         lingering copies of the node state in the network.  This may
         occur normally once due to the local node restarting and not
         storing the most recently used sequence number.  If this occurs
         more than once or for nodes not republishing their own node
         data, the DNCP profile MUST provide guidance on how to handle
         these situations as it indicates the existence of another
         active node with the same node identifier.

      *  If the node identifier does not match the local node
         identifier, and one or more of the following conditions are
         true:

         +  The local information is outdated for the corresponding node
            (the local sequence number is less than that within the
            TLV).

         +  The local information is potentially incorrect (the local
            sequence number matches but the node data hash differs).

         +  There is no data for that node altogether.

         Then:

         +  If the TLV contains the Node Data field, it SHOULD also be
            verified by ensuring that the locally calculated hash of the
            node data matches the content of the H(Node Data) field
            within the TLV.  If they differ, the TLV SHOULD be ignored
            and not processed further.





Stenberg & Barth             Standards Track                   [Page 14]



RFC 7787           Distributed Node Consensus Protocol        April 2016


         +  If the TLV does not contain the Node Data field, and the
            H(Node Data) field within the TLV differs from the local
            node data hash for that node (or there is none), the
            receiver MUST reply with a Request Node State TLV
            (Section 7.1.2) for the corresponding node.

         +  Otherwise, the receiver MUST update its locally stored state
            for that node (node data based on the Node Data field if
            present, sequence number, and relative time) to match the
            received TLV.

      For comparison purposes of the sequence number, a looping
      comparison function MUST be used to avoid problems in case of
      overflow.  The comparison function a < b <=> ((a - b) % (2^32)) &
      (2^31) != 0 where (a % b) represents the remainder of a modulo b
      and (a & b) represents bitwise conjunction of a and b is
      RECOMMENDED unless the DNCP profile defines another.

   o  Any other TLV: TLVs not recognized by the receiver MUST be
      silently ignored unless they are sent within another TLV (for
      example, TLVs within the Node Data field of a Node State TLV).
      TLVs within the Node Data field of the Node State TLV not
      recognized by the receiver MUST be retained for distribution to
      other nodes and for calculation of the node data hash as described
      in Section 7.2.3 but are ignored for other purposes.

   If secure unicast transport is configured for an endpoint, any Node
   State TLVs received over insecure multicast MUST be silently ignored.

4.5.  Discovering, Adding, and Removing Peers

   Peer relations are established between neighbors using one or more
   mutually connected endpoints.  Such neighbors exchange information
   about network state and published data directly, and through
   transitivity, this information then propagates throughout the
   network.

   New peers are discovered using the regular unicast or multicast
   transport defined in the DNCP profile (Section 9).  This process is
   not distinguished from peer addition, i.e., an unknown peer is simply
   discovered by receiving regular DNCP protocol TLVs from it, and
   dedicated discovery messages or TLVs do not exist.  For unicast-only
   transports, the individual node's transport addresses are
   preconfigured or obtained using an external service discovery
   protocol.  In the presence of a multicast transport, messages from
   unknown peers are handled in the same way as multicast messages from
   peers that are already known; thus, new peers are simply discovered
   when sending their regular DNCP protocol TLVs using multicast.



Stenberg & Barth             Standards Track                   [Page 15]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   When receiving a Node Endpoint TLV (Section 7.2.1) on an endpoint
   from an unknown peer:

   o  If received over unicast, the remote node MUST be added as a peer
      on the endpoint, and a Peer TLV (Section 7.3.1) MUST be created
      for it.

   o  If received over multicast, the node MAY be sent a (possibly rate-
      limited) unicast Request Network State TLV (Section 7.1.1).

   If keep-alives specified in Section 6.1 are NOT sent by the peer
   (either the DNCP profile does not specify the use of keep-alives or
   the particular peer chooses not to send keep-alives), some other
   existing local transport-specific means (such as Ethernet carrier
   detection or TCP keep-alive) MUST be used to ensure its presence.  If
   the peer does not send keep-alives, and no means to verify presence
   of the peer are available, the peer MUST be considered no longer
   present, and it SHOULD NOT be added back as a peer until it starts
   sending keep-alives again.  When the peer is no longer present, the
   Peer TLV and the local DNCP peer state MUST be removed.  DNCP does
   not define an explicit message or TLV for indicating the termination
   of DNCP operation by the terminating node; however, a derived
   protocol could specify an extension, if the need arises.

   If the local endpoint is in the Multicast-Listen+Unicast transport
   mode, a Peer TLV (Section 7.3.1) MUST NOT be published for the peers
   not having the highest node identifier.

4.6.  Data Liveliness Validation

   Maintenance of the hash tree (Section 4.1) and thereby network state
   hash updates depend on up-to-date information on bidirectional node
   reachability derived from the contents of a topology graph.  This
   graph changes whenever nodes are added to or removed from the network
   or when bidirectional connectivity between existing nodes is
   established or lost.  Therefore, the graph MUST be updated either
   immediately or with a small delay shorter than the DNCP profile-
   defined Trickle Imin whenever:

   o  A Peer TLV or a whole node is added or removed, or

   o  The origination time (in milliseconds) of some node's node data is
      less than current time - 2^32 + 2^15.

   The artificial upper limit for the origination time is used to
   gracefully avoid overflows of the origination time and allow for the
   node to republish its data as noted in Section 7.2.3.




Stenberg & Barth             Standards Track                   [Page 16]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   The topology graph update starts with the local node marked as
   reachable and all other nodes marked as unreachable.  Other nodes are
   then iteratively marked as reachable using the following algorithm: A
   candidate not-yet-reachable node N with an endpoint NE is marked as
   reachable if there is a reachable node R with an endpoint RE that
   meets all of the following criteria:

   o  The origination time (in milliseconds) of R's node data is greater
      than current time - 2^32 + 2^15.

   o  R publishes a Peer TLV with:

      *  Peer Node Identifier = N's node identifier

      *  Peer Endpoint Identifier = NE's endpoint identifier

      *  Endpoint Identifier = RE's endpoint identifier

   o  N publishes a Peer TLV with:

      *  Peer Node Identifier = R's node identifier

      *  Peer Endpoint Identifier = RE's endpoint identifier

      *  Endpoint Identifier = NE's endpoint identifier

   The algorithm terminates when no more candidate nodes fulfilling
   these criteria can be found.

   DNCP nodes that have not been reachable in the most recent topology
   graph traversal MUST NOT be used for calculation of the network state
   hash, be provided to any applications that need to use the whole TLV
   graph, or be provided to remote nodes.  They MAY be forgotten
   immediately after the topology graph traversal; however, it is
   RECOMMENDED to keep them at least briefly to improve the speed of
   DNCP network state convergence.  This reduces the number of queries
   needed to reconverge during both initial network convergence and when
   a part of the network loses and regains bidirectional connectivity
   within that time period.

5.  Data Model

   This section describes the local data structures a minimal
   implementation might use.  This section is provided only as a
   convenience for the implementor.  Some of the optional extensions
   (Section 6) describe additional data requirements, and some optional
   parts of the core protocol may also require more.




Stenberg & Barth             Standards Track                   [Page 17]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   A DNCP node has:

   o  A data structure containing data about the most recently sent
      Request Network State TLVs (Section 7.1.1).  The simplest option
      is keeping a timestamp of the most recent request (required to
      fulfill reply rate limiting specified in Section 4.4).

   A DNCP node has the following for every DNCP node in the DNCP
   network:

   o  Node identifier: the unique identifier of the node.  The length,
      how it is produced, and how collisions are handled is up to the
      DNCP profile.

   o  Node data: the set of TLV tuples published by that particular
      node.  As they are transmitted in a particular order (see Node
      State TLV (Section 7.2.3) for details), maintaining the order
      within the data structure here may be reasonable.

   o  Latest sequence number: the 32-bit sequence number that is
      incremented any time the TLV set is published.  The comparison
      function used to compare them is described in Section 4.4.

   o  Origination time: the (estimated) time when the current TLV set
      with the current sequence number was published.  It is used to
      populate the Milliseconds Since Origination field in a Node State
      TLV (Section 7.2.3).  Ideally, it also has millisecond accuracy.

   Additionally, a DNCP node has a set of endpoints for which DNCP is
   configured to be used.  For each such endpoint, a node has:

   o  Endpoint identifier: the 32-bit opaque locally unique value
      identifying the endpoint within a node.  It SHOULD NOT be reused
      immediately after an endpoint is disabled.

   o  Trickle instance: the endpoint's Trickle instance with parameters
      I, T, and c (only on an endpoint in Multicast+Unicast transport
      mode).

   and one (or more) of the following:

   o  Interface: the assigned local network interface.

   o  Unicast address: the DNCP node it should connect with.

   o  Set of addresses: the DNCP nodes from which connections are
      accepted.




Stenberg & Barth             Standards Track                   [Page 18]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   For each remote (peer, endpoint) pair detected on a local endpoint, a
   DNCP node has:

   o  Node identifier: the unique identifier of the peer.

   o  Endpoint identifier: the unique endpoint identifier used by the
      peer.

   o  Peer address: the most recently used address of the peer
      (authenticated and authorized, if security is enabled).

   o  Trickle instance: the particular peer's Trickle instance with
      parameters I, T, and c (only on an endpoint in unicast mode, when
      using an unreliable unicast transport).

6.  Optional Extensions

   This section specifies extensions to the core protocol that a DNCP
   profile may specify to be used.

6.1.  Keep-Alives

   While DNCP provides mechanisms for discovery and adding new peers on
   an endpoint (Section 4.5), as well as state change notifications,
   another mechanism may be needed to get rid of old, no longer valid
   peers if the transport or lower layers do not provide one as noted in
   Section 4.6.

   If keep-alives are not specified in the DNCP profile, the rest of
   this subsection MUST be ignored.

   A DNCP profile MAY specify either per-endpoint (sent using multicast
   to all DNCP nodes connected to a multicast-enabled link) or per-peer
   (sent using unicast to each peer individually) keep-alive support.

   For every endpoint that a keep-alive is specified for in the DNCP
   profile, the endpoint-specific keep-alive interval MUST be
   maintained.  By default, it is DNCP_KEEPALIVE_INTERVAL.  If there is
   a local value that is preferred for that for any reason
   (configuration, energy conservation, media type, ...), it can be
   substituted instead.  If a non-default keep-alive interval is used on
   any endpoint, a DNCP node MUST publish an appropriate Keep-Alive
   Interval TLV(s) (Section 7.3.2) within its node data.








Stenberg & Barth             Standards Track                   [Page 19]



RFC 7787           Distributed Node Consensus Protocol        April 2016


6.1.1.  Data Model Additions

   The following additions to the Data Model (Section 5) are needed to
   support keep-alives:

   For each configured endpoint that has per-endpoint keep-alives
   enabled:

   o  Last sent: If a timestamp that indicates the last time a Network
      State TLV (Section 7.2.2) was sent over that interface.

   For each remote (peer, endpoint) pair detected on a local endpoint, a
   DNCP node has:

   o  Last contact timestamp: A timestamp that indicates the last time a
      consistent Network State TLV (Section 7.2.2) was received from the
      peer over multicast or when anything was received over unicast.
      Failing to update it for a certain amount of time as specified in
      Section 6.1.5 results in the removal of the peer.  When adding a
      new peer, it is initialized to the current time.

   o  Last sent: If per-peer keep-alives are enabled, a timestamp that
      indicates the last time a Network State TLV (Section 7.2.2) was
      sent to that point-to-point peer.  When adding a new peer, it is
      initialized to the current time.

6.1.2.  Per-Endpoint Periodic Keep-Alives

   If per-endpoint keep-alives are enabled on an endpoint in
   Multicast+Unicast transport mode, and if no traffic containing a
   Network State TLV (Section 7.2.2) has been sent to a particular
   endpoint within the endpoint-specific keep-alive interval, a Network
   State TLV (Section 7.2.2) MUST be sent on that endpoint, and a new
   Trickle interval started, as specified in step 2 of Section 4.2 of
   [RFC6206].  The actual sending time SHOULD be further delayed by a
   random time span in [0, Imin/2].

6.1.3.  Per-Peer Periodic Keep-Alives

   If per-peer keep-alives are enabled on a unicast-only endpoint, and
   if no traffic containing a Network State TLV (Section 7.2.2) has been
   sent to a particular peer within the endpoint-specific keep-alive
   interval, a Network State TLV (Section 7.2.2) MUST be sent to the
   peer, and a new Trickle interval started, as specified in step 2 of
   Section 4.2 of [RFC6206].






Stenberg & Barth             Standards Track                   [Page 20]



RFC 7787           Distributed Node Consensus Protocol        April 2016


6.1.4.  Received TLV Processing Additions

   If a TLV is received over unicast from the peer, the Last contact
   timestamp for the peer MUST be updated.

   On receipt of a Network State TLV (Section 7.2.2) that is consistent
   with the locally calculated network state hash, the Last contact
   timestamp for the peer MUST be updated in order to maintain it as a
   peer.

6.1.5.  Peer Removal

   For every peer on every endpoint, the endpoint-specific keep-alive
   interval must be calculated by looking for Keep-Alive Interval TLVs
   (Section 7.3.2) published by the node, and if none exist, use the
   default value of DNCP_KEEPALIVE_INTERVAL.  If the peer's Last contact
   timestamp has not been updated for at least a locally chosen
   potentially endpoint-specific keep-alive multiplier (defaults to
   DNCP_KEEPALIVE_MULTIPLIER) times the peer's endpoint-specific keep-
   alive interval, the Peer TLV for that peer and the local DNCP peer
   state MUST be removed.

6.2.  Support for Dense Multicast-Enabled Links

   This optimization is needed to avoid a state space explosion.  Given
   a large set of DNCP nodes publishing data on an endpoint that uses
   multicast on a link, every node will add a Peer TLV (Section 7.3.1)
   for each peer.  While Trickle limits the amount of traffic on the
   link in stable state to some extent, the total amount of data that is
   added to and maintained in the DNCP network given N nodes on a
   multicast-enabled link is O(N^2).  Additionally, if per-peer keep-
   alives are used, there will be O(N^2) keep-alives running on the link
   if the liveliness of peers is not ensured using some other way (e.g.,
   TCP connection lifetime, Layer 2 notification, or per-endpoint keep-
   alive).

   An upper bound for the number of peers that are allowed for a
   particular type of link that an endpoint in Multicast+Unicast
   transport mode is used on SHOULD be provided by a DNCP profile, but
   it MAY also be chosen at runtime.  The main consideration when
   selecting a bound (if any) for a particular type of link should be
   whether it supports multicast traffic and whether a too large number
   of peers case is likely to happen during the use of that DNCP profile
   on that particular type of link.  If neither is likely, there is
   little point specifying support for this for that particular link
   type.





Stenberg & Barth             Standards Track                   [Page 21]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   If a DNCP profile does not support this extension at all, the rest of
   this subsection MUST be ignored.  This is because when this extension
   is used, the state within the DNCP network only contains a subset of
   the full topology of the network.  Therefore, every node must be
   aware of the potential of it being used in a particular DNCP profile.

   If the specified upper bound is exceeded for some endpoint in
   Multicast+Unicast transport mode and if the node does not have the
   highest node identifier on the link, it SHOULD treat the endpoint as
   a unicast endpoint connected to the node that has the highest node
   identifier detected on the link, therefore transitioning to
   Multicast-listen+Unicast transport mode.  See Section 4.2 for
   implications on the specific endpoint behavior.  The nodes in
   Multicast-listen+Unicast transport mode MUST keep listening to
   multicast traffic to both receive messages from the node(s) still in
   Multicast+Unicast mode and react to nodes with a greater node
   identifier appearing.  If the highest node identifier present on the
   link changes, the remote unicast address of the endpoints in
   Multicast-Listen+Unicast transport mode MUST be changed.  If the node
   identifier of the local node is the highest one, the node MUST switch
   back to, or stay in, Multicast+Unicast mode and form peer
   relationships with all peers as specified in Section 4.5.

7.  Type-Length-Value Objects

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Type               |           Length              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Value (if any) (+padding (if any))              |
   ..
   |                     (variable # of bytes)                     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     (optional nested TLVs)                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Each TLV is encoded as:

   o  a 2-byte Type field

   o  a 2-byte Length field, which contains the length of the Value
      field in bytes; 0 means no value

   o  the value itself (if any)

   o  padding bytes with a value of zero up to the next 4-byte boundary
      if the Length is not divisible by 4



Stenberg & Barth             Standards Track                   [Page 22]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   While padding bytes MUST NOT be included in the number stored in the
   Length field of the TLV, if the TLV is enclosed within another TLV,
   then the padding is included in the enclosing TLV's Length value.

   Each TLV that does not define optional fields or variable-length
   content MAY be sent with additional sub-TLVs appended after the TLV
   to allow for extensibility.  When handling such TLV types, each node
   MUST accept received TLVs that are longer than the fixed fields
   specified for the particular type and ignore the sub-TLVs with either
   unknown types or types not supported within that particular TLV.  If
   any sub-TLVs are present, the Length field of the TLV describes the
   number of bytes from the first byte of the TLV's own Value (if any)
   to the last (padding) byte of the last sub-TLV.

   For example, type=123 (0x7b) TLV with value 'x' (120 = 0x78) is
   encoded as: 007B 0001 7800 0000.  If it were to have a sub-TLV of
   type=124 (0x7c) with value 'y', it would be encoded as 007B 000C 7800
   0000 007C 0001 7900 0000.

   In this section, the following special notation is used:

      .. = octet string concatenation operation.

      H(x) = non-cryptographic hash function specified by the DNCP
      profile.

   In addition to the TLV types defined in this document, TLV Types
   11-31 and 512-767 are unassigned and may be sequentially registered,
   starting at 11, by Standards Action [RFC5226] by extensions to DNCP
   that may be applicable in multiple DNCP profiles.

7.1.  Request TLVs

7.1.1.  Request Network State TLV

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Type: Request network state (1)|          Length: >= 0         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV is used to request response with a Network State TLV
   (Section 7.2.2) and all Node State TLVs (Section 7.2.3) (without node
   data).







Stenberg & Barth             Standards Track                   [Page 23]



RFC 7787           Distributed Node Consensus Protocol        April 2016


7.1.2.  Request Node State TLV

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Type: Request node state (2)  |          Length: > 0          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                        Node Identifier                        |
   |                  (length fixed in DNCP profile)               |
   ...
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV is used to request a Node State TLV (Section 7.2.3)
   (including node data) for the node with the matching node identifier.

7.2.  Data TLVs

7.2.1.  Node Endpoint TLV

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   Type: Node endpoint (3)     |          Length: > 4          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                        Node Identifier                        |
   |                  (length fixed in DNCP profile)               |
   ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Endpoint Identifier                      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV identifies both the local node's node identifier, as well as
   the particular endpoint's endpoint identifier.  Section 4.2 specifies
   when it is sent.
















Stenberg & Barth             Standards Track                   [Page 24]



RFC 7787           Distributed Node Consensus Protocol        April 2016


7.2.2.  Network State TLV

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type: Network state (4)    |          Length: > 0          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     H(sequence number of node 1 .. H(node data of node 1) ..  |
   |    .. sequence number of node N .. H(node data of node N))    |
   |                  (length fixed in DNCP profile)               |
   ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV contains the current network state hash calculated by its
   sender (Section 4.1 describes the algorithm).

7.2.3.  Node State TLV

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Type: Node state (5)     |          Length: > 8          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                        Node Identifier                        |
   |                  (length fixed in DNCP profile)               |
   ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       Sequence Number                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                Milliseconds Since Origination                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         H(Node Data)                          |
   |                  (length fixed in DNCP profile)               |
   ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       (optionally) Node Data (a set of nested TLVs)           |
   ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV represents the local node's knowledge about the published
   state of a node in the DNCP network identified by the Node Identifier
   field in the TLV.

   Every node, including the node publishing the node data, MUST update
   the Milliseconds Since Origination whenever it sends a Node State TLV
   based on when the node estimates the data was originally published.
   This is, e.g., to ensure that any relative timestamps contained
   within the published node data can be correctly offset and



Stenberg & Barth             Standards Track                   [Page 25]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   interpreted.  Ultimately, what is provided is just an approximation,
   as transmission delays are not accounted for.

   Absent any changes, if the originating node notices that the 32-bit
   Milliseconds Since Origination value would be close to overflow
   (greater than 2^32 - 2^16), the node MUST republish its TLVs even if
   there is no change.  In other words, absent any other changes, the
   TLV set MUST be republished roughly every 48 days.

   The actual node data of the node may be included within the TLV as
   well as in the optional Node Data field.  The set of TLVs MUST be
   strictly ordered based on ascending binary content (including TLV
   type and length).  This enables, e.g., efficient state delta
   processing and no-copy indexing by TLV type by the recipient.  The
   node data content MUST be passed along exactly as it was received.
   It SHOULD be also verified on receipt that the locally calculated
   H(Node Data) matches the content of the field within the TLV, and if
   the hash differs, the TLV SHOULD be ignored.

7.3.  Data TLVs within Node State TLV

   These TLVs are published by the DNCP nodes and are therefore only
   encoded in the Node Data field of Node State TLVs.  If encountered
   outside Node State TLV, they MUST be silently ignored.

7.3.1.  Peer TLV

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       Type: Peer (8)          |          Length: > 8          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Peer Node Identifier                     |
   |                  (length fixed in DNCP profile)               |
   ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                    Peer Endpoint Identifier                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                   (Local) Endpoint Identifier                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV indicates that the node in question vouches that the
   specified peer is reachable by it on the specified local endpoint.
   The presence of this TLV at least guarantees that the node publishing
   it has received traffic from the peer recently.  For guaranteed up-
   to-date bidirectional reachability, the existence of both nodes'
   matching Peer TLVs needs to be checked.




Stenberg & Barth             Standards Track                   [Page 26]



RFC 7787           Distributed Node Consensus Protocol        April 2016


7.3.2.  Keep-Alive Interval TLV

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Type: Keep-alive interval (9) |          Length: >= 8         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Endpoint Identifier                      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                           Interval                            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV indicates a non-default interval being used to send keep-
   alives as specified in Section 6.1.

   Endpoint identifier is used to identify the particular (local)
   endpoint for which the interval applies on the sending node.  If 0,
   it applies for ALL endpoints for which no specific TLV exists.

   Interval specifies the interval in milliseconds at which the node
   sends keep-alives.  A value of zero means no keep-alives are sent at
   all; in that case, some lower-layer mechanism that ensures the
   presence of nodes MUST be available and used.

8.  Security and Trust Management

   If specified in the DNCP profile, either DTLS [RFC6347] or TLS
   [RFC5246] may be used to authenticate and encrypt either some (if
   specified optional in the profile) or all unicast traffic.  The
   following methods for establishing trust are defined, but it is up to
   the DNCP profile to specify which ones may, should, or must be
   supported.

8.1.  Trust Method Based on Pre-Shared Key

   A trust model based on Pre-Shared Key (PSK) is a simple security
   management mechanism that allows an administrator to deploy devices
   to an existing network by configuring them with a predefined key,
   similar to the configuration of an administrator password or Wi-Fi
   Protected Access (WPA) key.  Although limited in nature, it is useful
   to provide a user-friendly security mechanism for smaller networks.










Stenberg & Barth             Standards Track                   [Page 27]



RFC 7787           Distributed Node Consensus Protocol        April 2016


8.2.  PKI-Based Trust Method

   A PKI-based trust model enables more advanced management capabilities
   at the cost of increased complexity and bootstrapping effort.
   However, it allows trust to be managed in a centralized manner and is
   therefore useful for larger networks with a need for an authoritative
   trust management.

8.3.  Certificate-Based Trust Consensus Method

   For some scenarios -- such as bootstrapping a mostly unmanaged
   network -- the methods described above may not provide a desirable
   trade-off between security and user experience.  This section
   includes guidance for implementing an opportunistic security
   [RFC7435] method that DNCP profiles can build upon and adapt for
   their specific requirements.

   The certificate-based consensus model is designed to be a compromise
   between trust management effort and flexibility.  It is based on
   X.509 certificates and allows each DNCP node to provide a trust
   verdict on any other certificate, and a consensus is found to
   determine whether a node using this certificate or any certificate
   signed by it is to be trusted.

   A DNCP node not using this security method MUST ignore all announced
   trust verdicts and MUST NOT announce any such verdicts by itself,
   i.e., any other normative language in this subsection does not apply
   to it.

   The current effective trust verdict for any certificate is defined as
   the one with the highest priority from all trust verdicts announced
   for said certificate at the time.

8.3.1.  Trust Verdicts

   Trust verdicts are statements of DNCP nodes about the trustworthiness
   of X.509 certificates.  There are 5 possible trust verdicts in order
   of ascending priority:

      0 (Neutral): no trust verdict exists, but the DNCP network should
      determine one.

      1 (Cached Trust): the last known effective trust verdict was
      Configured or Cached Trust.

      2 (Cached Distrust): the last known effective trust verdict was
      Configured or Cached Distrust.




Stenberg & Barth             Standards Track                   [Page 28]



RFC 7787           Distributed Node Consensus Protocol        April 2016


      3 (Configured Trust): trustworthy based upon an external ceremony
      or configuration.

      4 (Configured Distrust): not trustworthy based upon an external
      ceremony or configuration.

   Trust verdicts are differentiated in 3 groups:

   o  Configured verdicts are used to announce explicit trust verdicts a
      node has based on any external trust bootstrap or predefined
      relations a node has formed with a given certificate.

   o  Cached verdicts are used to retain the last known trust state in
      case all nodes with configured verdicts about a given certificate
      have been disconnected or turned off.

   o  The Neutral verdict is used to announce a new node intending to
      join the network, so a final verdict for it can be found.

   The current effective trust verdict for any certificate is defined as
   the one with the highest priority within the set of trust verdicts
   announced for the certificate in the DNCP network.  A node MUST be
   trusted for participating in the DNCP network if and only if the
   current effective trust verdict for its own certificate or any one in
   its certificate hierarchy is (Cached or Configured) Trust, and none
   of the certificates in its hierarchy have an effective trust verdict
   of (Cached or Configured) Distrust.  In case a node has a configured
   verdict, which is different from the current effective trust verdict
   for a certificate, the current effective trust verdict takes
   precedence in deciding trustworthiness.  Despite that, the node still
   retains and announces its configured verdict.

8.3.2.  Trust Cache

   Each node SHOULD maintain a trust cache containing the current
   effective trust verdicts for all certificates currently announced in
   the DNCP network.  This cache is used as a backup of the last known
   state in case there is no node announcing a configured verdict for a
   known certificate.  It SHOULD be saved to a non-volatile memory at
   reasonable time intervals to survive a reboot or power outage.

   Every time a node (re)joins the network or detects the change of an
   effective trust verdict for any certificate, it will synchronize its
   cache, i.e., store new effective trust verdicts overwriting any
   previously cached verdicts.  Configured verdicts are stored in the
   cache as their respective cached counterparts.  Neutral verdicts are
   never stored and do not override existing cached verdicts.




Stenberg & Barth             Standards Track                   [Page 29]



RFC 7787           Distributed Node Consensus Protocol        April 2016


8.3.3.  Announcement of Verdicts

   A node SHOULD always announce any configured verdicts it has
   established by itself, and it MUST do so if announcing the configured
   verdict leads to a change in the current effective trust verdict for
   the respective certificate.  In absence of configured verdicts, it
   MUST announce Cached Trust verdicts it has stored in its trust cache,
   if one of the following conditions applies:

   o  The stored trust verdict is Cached Trust, and the current
      effective trust verdict for the certificate is Neutral or does not
      exist.

   o  The stored trust verdict is Cached Distrust, and the current
      effective trust verdict for the certificate is Cached Trust.

   A node rechecks these conditions whenever it detects changes of
   announced trust verdicts anywhere in the network.

   Upon encountering a node with a hierarchy of certificates for which
   there is no effective trust verdict, a node adds a Neutral Trust-
   Verdict TLV to its node data for all certificates found in the
   hierarchy and publishes it until an effective trust verdict different
   from Neutral can be found for any of the certificates, or a
   reasonable amount of time (10 minutes is suggested) with no reaction
   and no further authentication attempts has passed.  Such trust
   verdicts SHOULD also be limited in rate and number to prevent
   denial-of-service attacks.























Stenberg & Barth             Standards Track                   [Page 30]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   Trust verdicts are announced using Trust-Verdict TLVs:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   Type: Trust-Verdict (10)    |        Length: > 36           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Verdict    |                 (reserved)                    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   |                                                               |
   |                                                               |
   |                      SHA-256 Fingerprint                      |
   |                                                               |
   |                                                               |
   |                                                               |
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                          Common Name                          |

      Verdict represents the numerical index of the trust verdict.

      (reserved) is reserved for future additions and MUST be set to 0
      when creating TLVs and ignored when parsing them.

      SHA-256 Fingerprint contains the SHA-256 [RFC6234] hash value of
      the certificate in DER format.

      Common name contains the variable-length (1-64 bytes) common name
      of the certificate.

8.3.4.  Bootstrap Ceremonies

   The following non-exhaustive list of methods describes possible ways
   to establish trust relationships between DNCP nodes and node
   certificates.  Trust establishment is a two-way process in which the
   existing network must trust the newly added node, and the newly added
   node must trust at least one of its peer nodes.  It is therefore
   necessary that both the newly added node and an already trusted node
   perform such a ceremony to successfully introduce a node into the
   DNCP network.  In all cases, an administrator MUST be provided with
   external means to identify the node belonging to a certificate based
   on its fingerprint and a meaningful common name.








Stenberg & Barth             Standards Track                   [Page 31]



RFC 7787           Distributed Node Consensus Protocol        April 2016


8.3.4.1.  Trust by Identification

   A node implementing certificate-based trust MUST provide an interface
   to retrieve the current set of effective trust verdicts,
   fingerprints, and names of all certificates currently known and set
   configured verdicts to be announced.  Alternatively, it MAY provide a
   companion DNCP node or application with these capabilities with which
   it has a pre-established trust relationship.

8.3.4.2.  Preconfigured Trust

   A node MAY be preconfigured to trust a certain set of node or CA
   certificates.  However, such trust relationships MUST NOT result in
   unwanted or unrelated trust for nodes not intended to be run inside
   the same network (e.g., all other devices by the same manufacturer).

8.3.4.3.  Trust on Button Press

   A node MAY provide a physical or virtual interface to put one or more
   of its internal network interfaces temporarily into a mode in which
   it trusts the certificate of the first DNCP node it can successfully
   establish a connection with.

8.3.4.4.  Trust on First Use

   A node that is not associated with any other DNCP node MAY trust the
   certificate of the first DNCP node it can successfully establish a
   connection with.  This method MUST NOT be used when the node has
   already associated with any other DNCP node.

9.  DNCP Profile-Specific Definitions

   Each DNCP profile MUST specify the following aspects:

   o  Unicast and optionally a multicast transport protocol(s) to be
      used.  If a multicast-based node and status discovery is desired,
      a datagram-based transport supporting multicast has to be
      available.

   o  How the chosen transport(s) is secured: Not at all, optionally, or
      always with the TLS scheme defined here using one or more of the
      methods, or with something else.  If the links with DNCP nodes can
      be sufficiently secured or isolated, it is possible to run DNCP in
      a secure manner without using any form of authentication or
      encryption.






Stenberg & Barth             Standards Track                   [Page 32]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   o  Transport protocols' parameters such as port numbers to be used or
      multicast addresses to be used.  Unicast, multicast, and secure
      unicast may each require different parameters, if applicable.

   o  When receiving TLVs, what sort of TLVs are ignored in addition --
      as specified in Section 4.4 -- e.g., for security reasons.  While
      the security of the node data published within the Node State TLVs
      is already ensured by the base specification (if secure unicast
      transport is used, Node State TLVs are sent only via unicast as
      multicast ones are ignored on receipt), if a profile adds TLVs
      that are sent outside the node data, a profile should indicate
      whether or not those TLVs should be ignored if they are received
      via multicast or non-secured unicast.  A DNCP profile may define
      the following DNCP TLVs to be safely ignored:

      *  Anything received over multicast, except Node Endpoint TLV
         (Section 7.2.1) and Network State TLV (Section 7.2.2).

      *  Any TLVs received over unreliable unicast or multicast at a
         rate that is that is too high; Trickle will ensure eventual
         convergence given the rate slows down at some point.

   o  How to deal with node identifier collision as described in
      Section 4.4.  Main options are either for one or both nodes to
      assign new node identifiers to themselves or to notify someone
      about a fatal error condition in the DNCP network.

   o  Imin, Imax, and k ranges to be suggested for implementations to be
      used in the Trickle algorithm.  The Trickle algorithm does not
      require these to be the same across all implementations for it to
      work, but similar orders of magnitude help implementations of a
      DNCP profile to behave more consistently and to facilitate
      estimation of lower and upper bounds for convergence behavior of
      the network.

   o  Hash function H(x) to be used, and how many bits of the output are
      actually used.  The chosen hash function is used to handle both
      hashing of node data and producing network state hash, which is a
      hash of node data hashes.  SHA-256 defined in [RFC6234] is the
      recommended default choice, but a non-cryptographic hash function
      could be used as well.  If there is a hash collision in the
      network state hash, the network will effectively be partitioned to
      partitions that believe they are up to date but are actually no
      longer converged.  The network will converge either when some node
      data anywhere in the network changes or when conflicting Node
      State TLVs get transmitted across the partition (either caused by
      "Trickle-Driven Status Updates" (Section 4.3) or as part of the
      "Processing of Received TLVs" (Section 4.4)).  If a node publishes



Stenberg & Barth             Standards Track                   [Page 33]



RFC 7787           Distributed Node Consensus Protocol        April 2016


      node data with a hash that collides with any previously published
      node data, the update may not be (fully) propagated, and the old
      version of node data may be used instead.

   o  DNCP_NODE_IDENTIFIER_LENGTH: The fixed length of a node identifier
      (in bytes).

   o  Whether to send keep-alives, and if so, whether it is per-endpoint
      (requires multicast transport) or per-peer.  Keep-alive also has
      associated parameters:

      *  DNCP_KEEPALIVE_INTERVAL: How often keep-alives are to be sent
         by default (if enabled).

      *  DNCP_KEEPALIVE_MULTIPLIER: How many times the
         DNCP_KEEPALIVE_INTERVAL (or peer-supplied keep-alive interval
         value) node may not be heard from to be considered still valid.
         This is just a default used in absence of any other
         configuration information or particular per-endpoint
         configuration.

   o  Whether to support dense multicast-enabled link optimization
      (Section 6.2) or not.

   For some guidance on choosing transport and security options, please
   see Appendix B.

10.  Security Considerations

   DNCP-based protocols may use multicast to indicate DNCP state changes
   and for keep-alive purposes.  However, no actual published data TLVs
   will be sent across that channel.  Therefore, an attacker may only
   learn hash values of the state within DNCP and may be able to trigger
   unicast synchronization attempts between nodes on a local link this
   way.  A DNCP node MUST therefore rate limit its reactions to
   multicast packets.

   When using DNCP to bootstrap a network, PKI-based solutions may have
   issues when validating certificates due to potentially unavailable
   accurate time or due to the inability to use the network to either
   check Certificate Revocation Lists or perform online validation.

   The Certificate-based trust consensus mechanism defined in this
   document allows for a consenting revocation; however, in case of a
   compromised device, the trust cache may be poisoned before the actual
   revocation happens allowing the distrusted device to rejoin the
   network using a different identity.  Stopping such an attack might
   require physical intervention and flushing of the trust caches.



Stenberg & Barth             Standards Track                   [Page 34]



RFC 7787           Distributed Node Consensus Protocol        April 2016


11.  IANA Considerations

   IANA has set up a registry for the (decimal 16-bit) "DNCP TLV Types"
   under "Distributed Node Consensus Protocol (DNCP)".  The registration
   procedure is Standards Action [RFC5226].  The initial contents are:

      0: Reserved

      1: Request network state

      2: Request node state

      3: Node endpoint

      4: Network state

      5: Node state

      6: Reserved for future use (was: Custom)

      7: Reserved for future use (was: Fragment count)

      8: Peer

      9: Keep-alive interval

      10: Trust-Verdict

      11-31: Unassigned

      32-511: Reserved for per-DNCP profile use

      512-767: Unassigned

      768-1023: Reserved for Private Use [RFC5226]

      1024-65535: Reserved for future use














Stenberg & Barth             Standards Track                   [Page 35]



RFC 7787           Distributed Node Consensus Protocol        April 2016


12.  References

12.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC5226]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", BCP 26, RFC 5226,
              DOI 10.17487/RFC5226, May 2008,
              <http://www.rfc-editor.org/info/rfc5226>.

   [RFC6206]  Levis, P., Clausen, T., Hui, J., Gnawali, O., and J. Ko,
              "The Trickle Algorithm", RFC 6206, DOI 10.17487/RFC6206,
              March 2011, <http://www.rfc-editor.org/info/rfc6206>.

   [RFC6234]  Eastlake 3rd, D. and T. Hansen, "US Secure Hash Algorithms
              (SHA and SHA-based HMAC and HKDF)", RFC 6234,
              DOI 10.17487/RFC6234, May 2011,
              <http://www.rfc-editor.org/info/rfc6234>.

12.2.  Informative References

   [RFC3315]  Droms, R., Ed., Bound, J., Volz, B., Lemon, T., Perkins,
              C., and M. Carney, "Dynamic Host Configuration Protocol
              for IPv6 (DHCPv6)", RFC 3315, DOI 10.17487/RFC3315, July
              2003, <http://www.rfc-editor.org/info/rfc3315>.

   [RFC3493]  Gilligan, R., Thomson, S., Bound, J., McCann, J., and W.
              Stevens, "Basic Socket Interface Extensions for IPv6",
              RFC 3493, DOI 10.17487/RFC3493, February 2003,
              <http://www.rfc-editor.org/info/rfc3493>.

   [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246,
              DOI 10.17487/RFC5246, August 2008,
              <http://www.rfc-editor.org/info/rfc5246>.

   [RFC6347]  Rescorla, E. and N. Modadugu, "Datagram Transport Layer
              Security Version 1.2", RFC 6347, DOI 10.17487/RFC6347,
              January 2012, <http://www.rfc-editor.org/info/rfc6347>.

   [RFC7435]  Dukhovni, V., "Opportunistic Security: Some Protection
              Most of the Time", RFC 7435, DOI 10.17487/RFC7435,
              December 2014, <http://www.rfc-editor.org/info/rfc7435>.




Stenberg & Barth             Standards Track                   [Page 36]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   [RFC7596]  Cui, Y., Sun, Q., Boucadair, M., Tsou, T., Lee, Y., and I.
              Farrer, "Lightweight 4over6: An Extension to the Dual-
              Stack Lite Architecture", RFC 7596, DOI 10.17487/RFC7596,
              July 2015, <http://www.rfc-editor.org/info/rfc7596>.















































Stenberg & Barth             Standards Track                   [Page 37]



RFC 7787           Distributed Node Consensus Protocol        April 2016

Appendix A.  Alternative Modes of Operation

   Beyond what is described in the main text, the protocol allows for
   other uses.  These are provided as examples.

A.1.  Read-Only Operation

   If a node uses just a single endpoint and does not need to publish
   any TLVs, full DNCP node functionality is not required.  Such a
   limited node can acquire and maintain a view of the TLV space by
   implementing the processing logic as specified in Section 4.4.  Such
   node would not need Trickle, peer-maintenance, or even keep-alives at
   all, as the DNCP nodes' use of it would guarantee eventual receipt of
   network state hashes, and synchronization of node data, even in the
   presence of unreliable transport.

A.2.  Forwarding Operation

   If a node with a pair of endpoints does not need to publish any TLVs,
   it can detect (for example) nodes with the highest node identifier on
   each of the endpoints (if any).  Any TLVs received from one of them
   would be forwarded verbatim as unicast to the other node with the
   highest node identifier.

   Any tinkering with the TLVs would remove guarantees of this scheme
   working; however, passive monitoring would obviously be fine.  This
   type of simple forwarding cannot be chained, as it does not send
   anything proactively.

Appendix B.  DNCP Profile Additional Guidance

   This appendix explains implications of design choices made when
   specifying the DNCP profile to use particular transport or security
   options.

B.1.  Unicast Transport -- UDP or TCP?

   The node data published by a DNCP node is limited to 64 KB due to the
   16-bit size of the length field of the TLV it is published within.
   Some transport choices may decrease this limit; if using, e.g., UDP
   datagrams for unicast transport, the upper bound of the node data
   size is whatever the nodes and the underlying network can pass to
   each other as DNCP does not define its own fragmentation scheme.  A
   profile that chooses UDP has to be limited to small node data (e.g.,
   somewhat smaller than IPv6 default MTU if using IPv6) or specify a
   minimum that all nodes have to support.  Even then, if using
   non-link-local communications, there is some concern about what
   middleboxes do to fragmented packets.  Therefore, the use of stream



Stenberg & Barth             Standards Track                   [Page 38]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   transport such as TCP is probably a good idea if either
   non-link-local communication is desired or fragmentation is expected
   to cause problems.

   TCP also provides some other facilities, such as a relatively long
   built-in keep-alive, which in conjunction with connection closes
   occurring from eventual failed retransmissions may be sufficient to
   avoid the use of in-protocol keep-alive defined in Section 6.1.
   Additionally, it is reliable, so there is no need for Trickle on such
   unicast connections.

   The major downside of using TCP instead of UDP with DNCP-based
   profiles lies in the loss of control over the time at which TLVs are
   received; while unreliable UDP datagrams also have some delay, TLVs
   within reliable stream transport may be delayed significantly due to
   retransmissions.  This is not a problem if no relative time-dependent
   information is stored within the TLVs in the DNCP-based protocol; for
   such a protocol, TCP is a reasonable choice for unicast transport if
   it is available.

B.2.  (Optional) Multicast Transport

   Multicast is needed for dynamic peer discovery and to trigger unicast
   exchanges; for that, unreliable datagram transport (=typically UDP)
   is the only transport option defined within this specification,
   although DNCP-based protocols may themselves define some other
   transport or peer discovery mechanism (e.g., based on Multicast DNS
   (mDNS) or DNS).

   If multicast is used, a well-known address should be specified and
   for, e.g., IPv6, respectively, the desired address scopes.  In most
   cases, link-local and possibly site-local are useful scopes.

B.3.  (Optional) Transport Security

   In terms of provided security, DTLS and TLS are equivalent; they also
   consume a similar amount of state on the devices.  While TLS is on
   top of a stream protocol, using DTLS also requires relatively long
   session caching within the DTLS layer to avoid expensive
   reauthentication/authorization steps if and when any state within the
   DNCP network changes or per-peer keep-alive (if enabled) is sent.

   TLS implementations (at the time of writing the specification) seem
   more mature and available (as open source) than DTLS ones.  This may
   be due to a long history of use with HTTPS.






Stenberg & Barth             Standards Track                   [Page 39]



RFC 7787           Distributed Node Consensus Protocol        April 2016


   Some libraries seem not to support multiplexing between insecure and
   secure communication on the same port, so specifying distinct ports
   for secured and unsecured communication may be beneficial.

Appendix C.  Example Profile

   This is the DNCP profile of SHSP, an experimental (and for the
   purposes of this document fictional) home automation protocol.  The
   protocol itself is used to make a key-value store published by each
   of the nodes available to all other nodes for distributed monitoring
   and control of a home infrastructure.  It defines only one additional
   TLV type: a key=value TLV that contains a single key=value assignment
   for publication.

   o  Unicast transport: IPv6 TCP on port EXAMPLE-P1 since only absolute
      timestamps are used within the key=value data and since it focuses
      primarily on Linux-based nodes that support both protocols as
      well.  Connections from and to non-link-local addresses are
      ignored to avoid exposing this protocol outside the secure links.

   o  Multicast transport: IPv6 UDP on port EXAMPLE-P2 to link-local
      scoped multicast address ff02:EXAMPLE.  At least one node per link
      in the home is assumed to facilitate node discovery without
      depending on any other infrastructure.

   o  Security: None.  It is to be used only on trusted links (WPA2-x
      wireless, physically secure wired links).

   o  Additional TLVs to be ignored: None.  No DNCP security is
      specified, and no new TLVs are defined outside of node data.

   o  Node identifier length (DNCP_NODE_IDENTIFIER_LENGTH): 32 bits that
      are randomly generated.

   o  Node identifier collision handling: Pick new random node
      identifier.

   o  Trickle parameters: Imin = 200 ms, Imax = 7, k = 1.  It means at
      least one multicast per link in 25 seconds in stable state (0.2 *
      2^7).

   o  Hash function H(x) + length: SHA-256, only 128 bits used.  It's
      relatively fast, and 128 bits should be plenty to prevent random
      conflicts (64 bits would most likely be sufficient, too).

   o  No in-protocol keep-alives (Section 6.1); TCP keep-alive is to be
      used.  In practice, TCP keep-alive is seldom encountered anyway,
      as changes in network state cause packets to be sent on the



Stenberg & Barth             Standards Track                   [Page 40]



RFC 7787           Distributed Node Consensus Protocol        April 2016


      unicast connections, and those that fail sufficiently many
      retransmissions are dropped much before the keep-alive actually
      would fire.

   o  No support for dense multicast-enabled link optimization
      (Section 6.2); SHSP is a simple protocol for a few nodes (network
      wide, not even to mention on a single link) and therefore would
      not provide any benefit.

Acknowledgements

   Thanks to Ole Troan, Pierre Pfister, Mark Baugher, Mark Townsley,
   Juliusz Chroboczek, Jiazi Yi, Mikael Abrahamsson, Brian Carpenter,
   Thomas Clausen, DENG Hui, and Margaret Cullen for their contributions
   to the document.

   Thanks to Kaiwen Jin and Xavier Bonnetain for their related research
   work.

Authors' Addresses

   Markus Stenberg
   Independent
   Helsinki  00930
   Finland

   Email: markus.stenberg@iki.fi


   Steven Barth
   Independent
   Halle  06114
   Germany

   Email: cyrus@openwrt.org
















Stenberg & Barth             Standards Track                   [Page 41]



©2018 Martin Webb