You are here: irt.org | RFCs | RFC6536 [ previous next ]
Internet Engineering Task Force (IETF) A. Bierman Request for Comments: 6536 YumaWorks Category: Standards Track M. Bjorklund ISSN: 2070-1721 Tail-f Systems March 2012 Network Configuration Protocol (NETCONF) Access Control Model Abstract The standardization of network configuration interfaces for use with the Network Configuration Protocol (NETCONF) requires a structured and secure operating environment that promotes human usability and multi-vendor interoperability. There is a need for standard mechanisms to restrict NETCONF protocol access for particular users to a pre-configured subset of all available NETCONF protocol operations and content. This document defines such an access control model. Status of This Memo This is an Internet Standards Track document. This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 5741. Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at http://www.rfc-editor.org/info/rfc6536. Copyright Notice Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Bierman & Bjorklund Standards Track [Page 1]
RFC 6536 NACM March 2012 Table of Contents 1. Introduction ....................................................3 1.1. Terminology ................................................3 2. Access Control Design Objectives ................................4 2.1. Access Control Points ......................................5 2.2. Simplicity .................................................5 2.3. Procedural Interface .......................................6 2.4. Datastore Access ...........................................6 2.5. Users and Groups ...........................................6 2.6. Maintenance ................................................6 2.7. Configuration Capabilities .................................7 2.8. Identifying Security-Sensitive Content .....................7 3. NETCONF Access Control Model (NACM) .............................8 3.1. Introduction ...............................................8 3.1.1. Features ............................................8 3.1.2. External Dependencies ...............................9 3.1.3. Message Processing Model ............................9 3.2. Datastore Access ..........................................11 3.2.1. Access Rights ......................................11 3.2.2. <get> and <get-config> Operations ..................12 3.2.3. <edit-config> Operation ............................12 3.2.4. <copy-config> Operation ............................13 3.2.5. <delete-config> Operation ..........................14 3.2.6. <commit> Operation .................................14 3.2.7. <discard-changes> Operation ........................14 3.2.8. <kill-session> Operation ...........................14 3.3. Model Components ..........................................15 3.3.1. Users ..............................................15 3.3.2. Groups .............................................15 3.3.3. Emergency Recovery Session .........................15 3.3.4. Global Enforcement Controls ........................15 3.3.4.1. enable-nacm Switch ........................15 3.3.4.2. read-default Switch .......................16 3.3.4.3. write-default Switch ......................16 3.3.4.4. exec-default Switch .......................16 3.3.4.5. enable-external-groups Switch .............17 3.3.5. Access Control Rules ...............................17 3.4. Access Control Enforcement Procedures .....................17 3.4.1. Initial Operation ..................................17 3.4.2. Session Establishment ..............................18 3.4.3. "access-denied" Error Handling .....................18 3.4.4. Incoming RPC Message Validation ....................18 3.4.5. Data Node Access Validation ........................21 3.4.6. Outgoing <notification> Authorization ..............23 3.5. Data Model Definitions ....................................26 3.5.1. Data Organization ..................................26 3.5.2. YANG Module ........................................26 Bierman & Bjorklund Standards Track [Page 2]
RFC 6536 NACM March 2012 3.6. IANA Considerations .......................................36 3.7. Security Considerations ...................................36 3.7.1. NACM Configuration and Monitoring Considerations ...37 3.7.2. General Configuration Issues .......................38 3.7.3. Data Model Design Considerations ...................40 4. References .....................................................40 4.1. Normative References ......................................40 4.2. Informative References ....................................41 Appendix A. Usage Examples .......................................42 A.1. <groups> Example ..........................................42 A.2. Module Rule Example .......................................43 A.3. Protocol Operation Rule Example ...........................44 A.4. Data Node Rule Example ....................................46 A.5. Notification Rule Example .................................48 1. Introduction The NETCONF protocol does not provide any standard mechanisms to restrict the protocol operations and content that each user is authorized to access. There is a need for interoperable management of the controlled access to administrator-selected portions of the available NETCONF content within a particular server. This document addresses access control mechanisms for the Operations and Content layers of NETCONF, as defined in [RFC6241]. It contains three main sections: 1. Access Control Design Objectives 2. NETCONF Access Control Model (NACM) 3. YANG Data Model (ietf-netconf-acm.yang) 1.1. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. The following terms are defined in [RFC6241] and are not redefined here: o client o datastore Bierman & Bjorklund Standards Track [Page 3]
RFC 6536 NACM March 2012 o protocol operation o server o session o user The following terms are defined in [RFC6020] and are not redefined here: o data node o data definition statement The following terms are used throughout this document: access control: A security feature provided by the NETCONF server that allows an administrator to restrict access to a subset of all NETCONF protocol operations and data, based on various criteria. access control model (ACM): A conceptual model used to configure and monitor the access control procedures desired by the administrator to enforce a particular access control policy. access control rule: The criterion used to determine if a particular NETCONF protocol operation will be permitted or denied. access operation: How a request attempts to access a conceptual object. One of "none", "read", "create", "delete", "update", or "execute". recovery session: A special administrative session that is given unlimited NETCONF access and is exempt from all access control enforcement. The mechanism(s) used by a server to control and identify whether or not a session is a recovery session are implementation specific and outside the scope of this document. write access: A shorthand for the "create", "delete", and "update" access operations. 2. Access Control Design Objectives This section documents the design objectives for the NETCONF Access Control Model presented in Section 3. Bierman & Bjorklund Standards Track [Page 4]
RFC 6536 NACM March 2012 2.1. Access Control Points NETCONF allows new protocol operations to be added at any time, and the YANG Data Modeling Language supports this feature. It is not possible to design an ACM for NETCONF that only focuses on a static set of protocol operations, like some other protocols. Since few assumptions can be made about an arbitrary protocol operation, the NETCONF architectural server components need to be protected at three conceptual control points. These access control points, described in Figure 1, are as follows: protocol operation: Permission to invoke specific protocol operations. datastore: Permission to read and/or alter specific data nodes within any datastore. notification: Permission to receive specific notification event types. +-------------+ +-------------+ client | protocol | | data node | request --> | operation | -------------> | access | | allowed? | datastore | allowed? | +-------------+ or state +-------------+ data access +----------------+ | notification | event --> | allowed? | +----------------+ Figure 1 2.2. Simplicity There is concern that a complicated ACM will not be widely deployed because it is too hard to use. It needs to be easy to do simple things and possible to do complex things, instead of hard to do everything. Configuration of the access control system needs to be as simple as possible. Simple and common tasks need to be easy to configure and require little expertise or domain-specific knowledge. Complex tasks are possible using additional mechanisms, which may require additional expertise. Bierman & Bjorklund Standards Track [Page 5]
RFC 6536 NACM March 2012 A single set of access control rules ought to be able to control all types of NETCONF protocol operation invocation, all datastore access, and all notification events. Access control ought to be defined with a small and familiar set of permissions, while still allowing full control of NETCONF datastore access. 2.3. Procedural Interface The NETCONF protocol uses a remote procedure call model and an extensible set of protocol operations. Access control for any possible protocol operation is necessary. 2.4. Datastore Access It is necessary to control access to specific nodes and subtrees within the NETCONF datastore, regardless of which protocol operation, standard or proprietary, was used to access the datastore. 2.5. Users and Groups It is necessary that access control rules for a single user or a configurable group of users can be configured. The ACM needs to support the concept of administrative groups, to support the well-established distinction between a root account and other types of less-privileged conceptual user accounts. These groups need to be configurable by the administrator. It is necessary that the user-to-group mapping can be delegated to a central server, such as a RADIUS server [RFC2865][RFC5607]. Since authentication is performed by the NETCONF transport layer and RADIUS performs authentication and service authorization at the same time, the underlying NETCONF transport needs to be able to report a set of group names associated with the user to the server. It is necessary that the administrator can disable the usage of these group names within the ACM. 2.6. Maintenance It ought to be possible to disable part or all of the access control model enforcement procedures without deleting any access control rules. Bierman & Bjorklund Standards Track [Page 6]
RFC 6536 NACM March 2012 2.7. Configuration Capabilities Suitable configuration and monitoring mechanisms are needed to allow an administrator to easily manage all aspects of the ACM's behavior. A standard data model, suitable for use with the <edit-config> protocol operation, needs to be available for this purpose. Access control rules to restrict access operations on specific subtrees within the configuration datastore need to be supported. 2.8. Identifying Security-Sensitive Content One of the most important aspects of the data model documentation, and biggest concerns during deployment, is the identification of security-sensitive content. This applies to protocol operations in NETCONF, not just data and notifications. It is mandatory for security-sensitive objects to be documented in the Security Considerations section of an RFC. This is nice, but it is not good enough, for the following reasons: o This documentation-only approach forces administrators to study the RFC and determine if there are any potential security risks introduced by a new data model. o If any security risks are identified, then the administrator must study some more RFC text and determine how to mitigate the security risk(s). o The ACM on each server must be configured to mitigate the security risks, e.g., require privileged access to read or write the specific data identified in the Security Considerations section. o If the ACM is not pre-configured, then there will be a time window of vulnerability after the new data model is loaded and before the new access control rules for that data model are configured, enabled, and debugged. Often, the administrator just wants to disable default access to the secure content, so no inadvertent or malicious changes can be made to the server. This allows the default rules to be more lenient, without significantly increasing the security risk. A data model designer needs to be able to use machine-readable statements to identify NETCONF content, which needs to be protected by default. This will allow client and server tools to automatically Bierman & Bjorklund Standards Track [Page 7]
RFC 6536 NACM March 2012 identify data-model-specific security risks, by denying access to sensitive data unless the user is explicitly authorized to perform the requested access operation. 3. NETCONF Access Control Model (NACM) 3.1. Introduction This section provides a high-level overview of the access control model structure. It describes the NETCONF protocol message processing model and the conceptual access control requirements within that model. 3.1.1. Features The NACM data model provides the following features: o Independent control of remote procedure call (RPC), data, and notification access. o Simple access control rules configuration data model that is easy to use. o The concept of an emergency recovery session is supported, but configuration of the server for this purpose is beyond the scope of this document. An emergency recovery session will bypass all access control enforcement, in order to allow it to initialize or repair the NACM configuration. o A simple and familiar set of datastore permissions is used. o Support for YANG security tagging (e.g., "nacm:default-deny-write" statement) allows default security modes to automatically exclude sensitive data. o Separate default access modes for read, write, and execute permissions. o Access control rules are applied to configurable groups of users. o The access control enforcement procedures can be disabled during operation, without deleting any access control rules, in order to debug operational problems. o Access control rules are simple to configure. Bierman & Bjorklund Standards Track [Page 8]
RFC 6536 NACM March 2012 o The number of denied protocol operation requests and denied datastore write requests can be monitored by the client. o Simple unconstrained YANG instance identifiers are used to configure access control rules for specific data nodes. 3.1.2. External Dependencies The NETCONF protocol [RFC6241] is used for all management purposes within this document. The YANG Data Modeling Language [RFC6020] is used to define the NETCONF data models specified in this document. 3.1.3. Message Processing Model The following diagram shows the conceptual message flow model, including the points at which access control is applied during NETCONF message processing. Bierman & Bjorklund Standards Track [Page 9]
RFC 6536 NACM March 2012 +-------------------------+ | session | | (username) | +-------------------------+ | ^ V | +--------------+ +---------------+ | message | | message | | dispatcher | | generator | +--------------+ +---------------+ | ^ ^ V | | +===========+ +-------------+ +----------------+ | <rpc> |---> | <rpc-reply> | | <notification> | | acc. ctl | | generator | | generator | +===========+ +-------------+ +----------------+ | ^ ^ ^ V +------+ | | +-----------+ | +=============+ +================+ | <rpc> | | | read | | <notification> | | processor |-+ | data node | | access ctl | | | | acc. ctl | | | +-----------+ +=============+ +================+ | | ^ ^ V +----------------+ | | +===========+ | | | | write | | | | | data node | | | | | acc. ctl | -----------+ | | | +===========+ | | | | | | | | | V V V | | +---------------+ +-----------------+ | configuration | ---> | server | | datastore | | instrumentation | | | <--- | | +---------------+ +-----------------+ Figure 2 The following high-level sequence of conceptual processing steps is executed for each received <rpc> message, if access control enforcement is enabled: o For each active session, access control is applied individually to all <rpc> messages (except <close-session>) received by the server, unless the session is identified as a recovery session. Bierman & Bjorklund Standards Track [Page 10]
RFC 6536 NACM March 2012 o If the user is authorized to execute the specified protocol operation, then processing continues; otherwise, the request is rejected with an "access-denied" error. o If the configuration datastore or conceptual state data is accessed by the protocol operation, then the server checks if the client is authorized to access the nodes in the datastore. If the user is authorized to perform the requested access operation on the requested data, then processing continues. The following sequence of conceptual processing steps is executed for each generated notification event, if access control enforcement is enabled: o Server instrumentation generates a notification for a particular subscription. o The notification access control enforcer checks the notification event type, and if it is one that the user is not authorized to read, then the notification is dropped for that subscription. 3.2. Datastore Access The same access control rules apply to all datastores, for example, the candidate configuration datastore or the running configuration datastore. Only the standard NETCONF datastores (candidate, running, and startup) are controlled by NACM. Local or remote files or datastores accessed via the <url> parameter are not controlled by NACM. 3.2.1. Access Rights A small set of hard-wired datastore access rights is needed to control access to all possible NETCONF protocol operations, including vendor extensions to the standard protocol operation set. The "CRUDX" model can support all NETCONF protocol operations: o Create: allows the client to add a new data node instance to a datastore. o Read: allows the client to read a data node instance from a datastore or receive the notification event type. o Update: allows the client to update an existing data node instance in a datastore. Bierman & Bjorklund Standards Track [Page 11]
RFC 6536 NACM March 2012 o Delete: allows the client to delete a data node instance from a datastore. o eXec: allows the client to execute the protocol operation. 3.2.2. <get> and <get-config> Operations Data nodes to which the client does not have read access are silently omitted from the <rpc-reply> message. This is done to allow NETCONF filters for <get> and <get-config> to function properly, instead of causing an "access-denied" error because the filter criteria would otherwise include unauthorized read access to some data nodes. For NETCONF filtering purposes, the selection criteria is applied to the subset of nodes that the user is authorized to read, not the entire datastore. 3.2.3. <edit-config> Operation The NACM access rights are not directly coupled to the <edit-config> "operation" attribute, although they are similar. Instead, a NACM access right applies to all protocol operations that would result in a particular access operation to the target datastore. This section describes how these access rights apply to the specific access operations supported by the <edit-config> protocol operation. If the effective access operation is "none" (i.e., default- operation="none") for a particular data node, then no access control is applied to that data node. This is required to allow access to a subtree within a larger data structure. For example, a user may be authorized to create a new "/interfaces/interface" list entry but not be authorized to create or delete its parent container ("/interfaces"). If the "/interfaces" container already exists in the target datastore, then the effective operation will be "none" for the "/interfaces" node if an "/interfaces/interface" list entry is edited. If the protocol operation would result in the creation of a datastore node and the user does not have "create" access permission for that node, the protocol operation is rejected with an "access-denied" error. If the protocol operation would result in the deletion of a datastore node and the user does not have "delete" access permission for that node, the protocol operation is rejected with an "access-denied" error. Bierman & Bjorklund Standards Track [Page 12]
RFC 6536 NACM March 2012 If the protocol operation would result in the modification of a datastore node and the user does not have "update" access permission for that node, the protocol operation is rejected with an "access- denied" error. A "merge" or "replace" <edit-config> operation may include data nodes that do not alter portions of the existing datastore. For example, a container or list node may be present for naming purposes but does not actually alter the corresponding datastore node. These unaltered data nodes are ignored by the server and do not require any access rights by the client. A "merge" <edit-config> operation may include data nodes but not include particular child data nodes that are present in the datastore. These missing data nodes within the scope of a "merge" <edit-config> operation are ignored by the server and do not require any access rights by the client. The contents of specific restricted datastore nodes MUST NOT be exposed in any <rpc-error> elements within the reply. 3.2.4. <copy-config> Operation Access control for the <copy-config> protocol operation requires special consideration because the administrator may be replacing the entire target datastore. If the source of the <copy-config> protocol operation is the running configuration datastore and the target is the startup configuration datastore, the client is only required to have permission to execute the <copy-config> protocol operation. Otherwise: o If the source of the <copy-config> operation is a datastore, then data nodes to which the client does not have read access are silently omitted. o If the target of the <copy-config> operation is a datastore, the client needs access to the modified nodes, specifically: * If the protocol operation would result in the creation of a datastore node and the user does not have "create" access permission for that node, the protocol operation is rejected with an "access-denied" error. Bierman & Bjorklund Standards Track [Page 13]
RFC 6536 NACM March 2012 * If the protocol operation would result in the deletion of a datastore node and the user does not have "delete" access permission for that node, the protocol operation is rejected with an "access-denied" error. * If the protocol operation would result in the modification of a datastore node and the user does not have "update" access permission for that node, the protocol operation is rejected with an "access-denied" error. 3.2.5. <delete-config> Operation Access to the <delete-config> protocol operation is denied by default. The "exec-default" leaf does not apply to this protocol operation. Access control rules must be explicitly configured to allow invocation by a non-recovery session. 3.2.6. <commit> Operation The server MUST determine the exact nodes in the running configuration datastore that are actually different and only check "create", "update", and "delete" access permissions for this set of nodes, which could be empty. For example, if a session can read the entire datastore but only change one leaf, that session needs to be able to edit and commit that one leaf. 3.2.7. <discard-changes> Operation The client is only required to have permission to execute the <discard-changes> protocol operation. No datastore permissions are needed. 3.2.8. <kill-session> Operation The <kill-session> operation does not directly alter a datastore. However, it allows one session to disrupt another session that is editing a datastore. Access to the <kill-session> protocol operation is denied by default. The "exec-default" leaf does not apply to this protocol operation. Access control rules must be explicitly configured to allow invocation by a non-recovery session. Bierman & Bjorklund Standards Track [Page 14]
RFC 6536 NACM March 2012 3.3. Model Components This section defines the conceptual components related to the access control model. 3.3.1. Users A "user" is the conceptual entity that is associated with the access permissions granted to a particular session. A user is identified by a string that is unique within the server. As described in [RFC6241], the username string is derived from the transport layer during session establishment. If the transport layer cannot authenticate the user, the session is terminated. 3.3.2. Groups Access to a specific NETCONF protocol operation is granted to a session, associated with a group, not a user. A group is identified by its name. All group names are unique within the server. A group member is identified by a username string. The same user can be a member of multiple groups. 3.3.3. Emergency Recovery Session The server MAY support a recovery session mechanism, which will bypass all access control enforcement. This is useful for restricting initial access and repairing a broken access control configuration. 3.3.4. Global Enforcement Controls There are five global controls that are used to help control how access control is enforced. 3.3.4.1. enable-nacm Switch A global "enable-nacm" on/off switch is provided to enable or disable all access control enforcement. When this global switch is set to "true", then all requests are checked against the access control rules and only permitted if configured to allow the specific access request. When this global switch is set to "false", then all access requested are permitted. Bierman & Bjorklund Standards Track [Page 15]
RFC 6536 NACM March 2012 3.3.4.2. read-default Switch An on/off "read-default" switch is provided to enable or disable default access to receive data in replies and notifications. When the "enable-nacm" global switch is set to "true", then this global switch is relevant if no matching access control rule is found to explicitly permit or deny read access to the requested NETCONF datastore data or notification event type. When this global switch is set to "permit" and no matching access control rule is found for the NETCONF datastore read or notification event requested, then access is permitted. When this global switch is set to "deny" and no matching access control rule is found for the NETCONF datastore read or notification event requested, then access is denied. 3.3.4.3. write-default Switch An on/off "write-default" switch is provided to enable or disable default access to alter configuration data. When the "enable-nacm" global switch is set to "true", then this global switch is relevant if no matching access control rule is found to explicitly permit or deny write access to the requested NETCONF datastore data. When this global switch is set to "permit" and no matching access control rule is found for the NETCONF datastore write requested, then access is permitted. When this global switch is set to "deny" and no matching access control rule is found for the NETCONF datastore write requested, then access is denied. 3.3.4.4. exec-default Switch An on/off "exec-default" switch is provided to enable or disable default access to execute protocol operations. When the "enable- nacm" global switch is set to "true", then this global switch is relevant if no matching access control rule is found to explicitly permit or deny access to the requested NETCONF protocol operation. When this global switch is set to "permit" and no matching access control rule is found for the NETCONF protocol operation requested, then access is permitted. When this global switch is set to "deny" and no matching access control rule is found for the NETCONF protocol operation requested, then access is denied. Bierman & Bjorklund Standards Track [Page 16]
RFC 6536 NACM March 2012 3.3.4.5. enable-external-groups Switch When this global switch is set to "true", the group names reported by the NETCONF transport layer for a session are used together with the locally configured group names to determine the access control rules for the session. When this switch is set to "false", the group names reported by the NETCONF transport layer are ignored by NACM. 3.3.5. Access Control Rules There are four types of rules available in NACM: module rule: controls access for definitions in a specific YANG module, identified by its name. protocol operation rule: controls access for a specific protocol operation, identified by its YANG module and name. data node rule: controls access for a specific data node, identified by its path location within the conceptual XML document for the data node. notification rule: controls access for a specific notification event type, identified by its YANG module and name. 3.4. Access Control Enforcement Procedures There are seven separate phases that need to be addressed, four of which are related to the NETCONF message processing model (Section 3.1.3). In addition, the initial startup mode for a NETCONF server, session establishment, and "access-denied" error-handling procedures also need to be considered. The server MUST use the access control rules in effect at the time it starts processing the message. The same access control rules MUST stay in effect for the processing of the entire message. 3.4.1. Initial Operation Upon the very first startup of the NETCONF server, the access control configuration will probably not be present. If it isn't, a server MUST NOT allow any write access to any session role except a recovery session. Bierman & Bjorklund Standards Track [Page 17]
RFC 6536 NACM March 2012 Access rules are enforced any time a request is initiated from a user session. Access control is not enforced for server-initiated access requests, such as the initial load of the running datastore, during bootup. 3.4.2. Session Establishment The access control model applies specifically to the well-formed XML content transferred between a client and a server after session establishment has been completed and after the <hello> exchange has been successfully completed. Once session establishment is completed and a user has been authenticated, the NETCONF transport layer reports the username and a possibly empty set of group names associated with the user to the NETCONF server. The NETCONF server will enforce the access control rules, based on the supplied username, group names, and the configuration data stored on the server. 3.4.3. "access-denied" Error Handling The "access-denied" error-tag is generated when the access control system denies access to either a request to invoke a protocol operation or a request to perform a particular access operation on the configuration datastore. A server MUST NOT include any information the client is not allowed to read in any <error-info> elements within the <rpc-error> response. 3.4.4. Incoming RPC Message Validation The diagram below shows the basic conceptual structure of the access control processing model for incoming NETCONF <rpc> messages within a server. Bierman & Bjorklund Standards Track [Page 18]
RFC 6536 NACM March 2012 NETCONF server +------------+ | XML | | message | | dispatcher | +------------+ | | V +------------+ | NC-base NS | | <rpc> | +------------+ | | | | | +-------------------------+ | +------------+ | V V V +-----------+ +---------------+ +------------+ | Vendor NS | | NC-base NS | | NC-base NS | | <my-edit> | | <edit-config> | | <unlock> | +-----------+ +---------------+ +------------+ | | | | V V +----------------------+ | | | configuration | | datastore | +----------------------+ Figure 3 Access control begins with the message dispatcher. After the server validates the <rpc> element and determines the namespace URI and the element name of the protocol operation being requested, the server verifies that the user is authorized to invoke the protocol operation. The server MUST separately authorize every protocol operation by following these steps: 1. If the "enable-nacm" leaf is set to "false", then the protocol operation is permitted. 2. If the requesting session is identified as a recovery session, then the protocol operation is permitted. Bierman & Bjorklund Standards Track [Page 19]
RFC 6536 NACM March 2012 3. If the requested operation is the NETCONF <close-session> protocol operation, then the protocol operation is permitted. 4. Check all the "group" entries for ones that contain a "user- name" entry that equals the username for the session making the request. If the "enable-external-groups" leaf is "true", add to these groups the set of groups provided by the transport layer. 5. If no groups are found, continue with step 10. 6. Process all rule-list entries, in the order they appear in the configuration. If a rule-list's "group" leaf-list does not match any of the user's groups, proceed to the next rule-list entry. 7. For each rule-list entry found, process all rules, in order, until a rule that matches the requested access operation is found. A rule matches if all of the following criteria are met: * The rule's "module-name" leaf is "*" or equals the name of the YANG module where the protocol operation is defined. * The rule does not have a "rule-type" defined or the "rule- type" is "protocol-operation" and the "rpc-name" is "*" or equals the name of the requested protocol operation. * The rule's "access-operations" leaf has the "exec" bit set or has the special value "*". 8. If a matching rule is found, then the "action" leaf is checked. If it is equal to "permit", then the protocol operation is permitted; otherwise, it is denied. 9. At this point, no matching rule was found in any rule-list entry. 10. If the requested protocol operation is defined in a YANG module advertised in the server capabilities and the "rpc" statement contains a "nacm:default-deny-all" statement, then the protocol operation is denied. 11. If the requested protocol operation is the NETCONF <kill- session> or <delete-config>, then the protocol operation is denied. 12. If the "exec-default" leaf is set to "permit", then permit the protocol operation; otherwise, deny the request. Bierman & Bjorklund Standards Track [Page 20]
RFC 6536 NACM March 2012 If the user is not authorized to invoke the protocol operation, then an <rpc-error> is generated with the following information: error-tag: access-denied error-path: Identifies the requested protocol operation. The following example represents the <edit-config> protocol operation in the NETCONF base namespace: <error-path xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0"> /nc:rpc/nc:edit-config </error-path> If a datastore is accessed, either directly or as a side effect of the protocol operation, then the server MUST intercept the access operation and make sure the user is authorized to perform the requested access operation on the specified data, as defined in Section 3.4.5. 3.4.5. Data Node Access Validation If a data node within a datastore is accessed, then the server MUST ensure that the user is authorized to perform the requested "read", "create", "update", or "delete" access operation on the specified data node. The data node access request is authorized by following these steps: 1. If the "enable-nacm" leaf is set to "false", then the access operation is permitted. 2. If the requesting session is identified as a recovery session, then the access operation is permitted. 3. Check all the "group" entries for ones that contain a "user- name" entry that equals the username for the session making the request. If the "enable-external-groups" leaf is "true", add to these groups the set of groups provided by the transport layer. 4. If no groups are found, continue with step 9. 5. Process all rule-list entries, in the order they appear in the configuration. If a rule-list's "group" leaf-list does not match any of the user's groups, proceed to the next rule-list entry. Bierman & Bjorklund Standards Track [Page 21]
RFC 6536 NACM March 2012 6. For each rule-list entry found, process all rules, in order, until a rule that matches the requested access operation is found. A rule matches if all of the following criteria are met: * The rule's "module-name" leaf is "*" or equals the name of the YANG module where the requested data node is defined. * The rule does not have a "rule-type" defined or the "rule- type" is "data-node" and the "path" matches the requested data node. * For a "read" access operation, the rule's "access-operations" leaf has the "read" bit set or has the special value "*". * For a "create" access operation, the rule's "access- operations" leaf has the "create" bit set or has the special value "*". * For a "delete" access operation, the rule's "access- operations" leaf has the "delete" bit set or has the special value "*". * For an "update" access operation, the rule's "access- operations" leaf has the "update" bit set or has the special value "*". 7. If a matching rule is found, then the "action" leaf is checked. If it is equal to "permit", then the data node access is permitted; otherwise, it is denied. For a "read" access operation, "denied" means that the requested data is not returned in the reply. 8. At this point, no matching rule was found in any rule-list entry. 9. For a "read" access operation, if the requested data node is defined in a YANG module advertised in the server capabilities and the data definition statement contains a "nacm:default-deny- all" statement, then the requested data node is not included in the reply. 10. For a "write" access operation, if the requested data node is defined in a YANG module advertised in the server capabilities and the data definition statement contains a "nacm:default-deny- write" or a "nacm:default-deny-all" statement, then the data node access request is denied. Bierman & Bjorklund Standards Track [Page 22]
RFC 6536 NACM March 2012 11. For a "read" access operation, if the "read-default" leaf is set to "permit", then include the requested data node in the reply; otherwise, do not include the requested data node in the reply. 12. For a "write" access operation, if the "write-default" leaf is set to "permit", then permit the data node access request; otherwise, deny the request. 3.4.6. Outgoing <notification> Authorization Configuration of access control rules specifically for descendant nodes of the notification event type element are outside the scope of this document. If the user is authorized to receive the notification event type, then it is also authorized to receive any data it contains. The following figure shows the conceptual message processing model for outgoing <notification> messages. Bierman & Bjorklund Standards Track [Page 23]
RFC 6536 NACM March 2012 NETCONF server +------------+ | XML | | message | | generator | +------------+ ^ | +----------------+ | <notification> | | generator | +----------------+ ^ | +=================+ | <notification> | | access control | | <eventType> | +=================+ ^ | +------------------------+ | server instrumentation | +------------------------+ | ^ V | +----------------------+ | configuration | | datastore | +----------------------+ Figure 4 The generation of a notification for a specific subscription [RFC5277] is authorized by following these steps: 1. If the "enable-nacm" leaf is set to "false", then the notification is permitted. 2. If the session is identified as a recovery session, then the notification is permitted. 3. If the notification is the NETCONF <replayComplete> or <notificationComplete> event type [RFC5277], then the notification is permitted. Bierman & Bjorklund Standards Track [Page 24]
RFC 6536 NACM March 2012 4. Check all the "group" entries for ones that contain a "user- name" entry that equals the username for the session making the request. If the "enable-external-groups" leaf is "true", add to these groups the set of groups provided by the transport layer. 5. If no groups are found, continue with step 10. 6. Process all rule-list entries, in the order they appear in the configuration. If a rule-list's "group" leaf-list does not match any of the user's groups, proceed to the next rule-list entry. 7. For each rule-list entry found, process all rules, in order, until a rule that matches the requested access operation is found. A rule matches if all of the following criteria are met: * The rule's "module-name" leaf is "*" or equals the name of the YANG module where the notification is defined. * The rule does not have a "rule-type" defined or the "rule- type" is "notification" and the "notification-name" is "*" and equals the name of the notification. * The rule's "access-operations" leaf has the "read" bit set or has the special value "*". 8. If a matching rule is found, then the "action" leaf is checked. If it is equal to "permit", then permit the notification; otherwise, drop the notification for the associated subscription. 9. Otherwise, no matching rule was found in any rule-list entry. 10. If the requested notification is defined in a YANG module advertised in the server capabilities and the "notification" statement contains a "nacm:default-deny-all" statement, then the notification is dropped for the associated subscription. 11. If the "read-default" leaf is set to "permit", then permit the notification; otherwise, drop the notification for the associated subscription. Bierman & Bjorklund Standards Track [Page 25]
RFC 6536 NACM March 2012 3.5. Data Model Definitions 3.5.1. Data Organization The following diagram highlights the contents and structure of the NACM YANG module. +--rw nacm +--rw enable-nacm? boolean +--rw read-default? action-type +--rw write-default? action-type +--rw exec-default? action-type +--rw enable-external-groups? boolean +--ro denied-operations yang:zero-based-counter32 +--ro denied-data-writes yang:zero-based-counter32 +--ro denied-notifications yang:zero-based-counter32 +--rw groups | +--rw group [name] | +--rw name group-name-type | +--rw user-name* user-name-type +--rw rule-list [name] +--rw name string +--rw group* union +--rw rule [name] +--rw name string +--rw module-name? union +--rw (rule-type)? | +--:(protocol-operation) | | +--rw rpc-name? union | +--:(notification) | | +--rw notification-name? union | +--:(data-node) | +--rw path node-instance-identifier +--rw access-operations? union +--rw action action-type +--rw comment? string 3.5.2. YANG Module The following YANG module specifies the normative NETCONF content that MUST by supported by the server. The "ietf-netconf-acm" YANG module imports typedefs from [RFC6021]. Bierman & Bjorklund Standards Track [Page 26]
RFC 6536 NACM March 2012 <CODE BEGINS> file "ietf-netconf-acm@2012-02-22.yang" module ietf-netconf-acm { namespace "urn:ietf:params:xml:ns:yang:ietf-netconf-acm"; prefix "nacm"; import ietf-yang-types { prefix yang; } organization "IETF NETCONF (Network Configuration) Working Group"; contact "WG Web: <http://tools.ietf.org/wg/netconf/> WG List: <mailto:netconf@ietf.org> WG Chair: Mehmet Ersue <mailto:mehmet.ersue@nsn.com> WG Chair: Bert Wijnen <mailto:bertietf@bwijnen.net> Editor: Andy Bierman <mailto:andy@yumaworks.com> Editor: Martin Bjorklund <mailto:mbj@tail-f.com>"; description "NETCONF Access Control Model. Copyright (c) 2012 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This version of this YANG module is part of RFC 6536; see the RFC itself for full legal notices."; revision "2012-02-22" { Bierman & Bjorklund Standards Track [Page 27]
RFC 6536 NACM March 2012 description "Initial version"; reference "RFC 6536: Network Configuration Protocol (NETCONF) Access Control Model"; } /* * Extension statements */ extension default-deny-write { description "Used to indicate that the data model node represents a sensitive security system parameter. If present, and the NACM module is enabled (i.e., /nacm/enable-nacm object equals 'true'), the NETCONF server will only allow the designated 'recovery session' to have write access to the node. An explicit access control rule is required for all other users. The 'default-deny-write' extension MAY appear within a data definition statement. It is ignored otherwise."; } extension default-deny-all { description "Used to indicate that the data model node controls a very sensitive security system parameter. If present, and the NACM module is enabled (i.e., /nacm/enable-nacm object equals 'true'), the NETCONF server will only allow the designated 'recovery session' to have read, write, or execute access to the node. An explicit access control rule is required for all other users. The 'default-deny-all' extension MAY appear within a data definition statement, 'rpc' statement, or 'notification' statement. It is ignored otherwise."; } /* * Derived types */ typedef user-name-type { type string { Bierman & Bjorklund Standards Track [Page 28]
RFC 6536 NACM March 2012 length "1..max"; } description "General Purpose Username string."; } typedef matchall-string-type { type string { pattern "\*"; } description "The string containing a single asterisk '*' is used to conceptually represent all possible values for the particular leaf using this data type."; } typedef access-operations-type { type bits { bit create { description "Any protocol operation that creates a new data node."; } bit read { description "Any protocol operation or notification that returns the value of a data node."; } bit update { description "Any protocol operation that alters an existing data node."; } bit delete { description "Any protocol operation that removes a data node."; } bit exec { description "Execution access to the specified protocol operation."; } } description "NETCONF Access Operation."; } typedef group-name-type { type string { Bierman & Bjorklund Standards Track [Page 29]
RFC 6536 NACM March 2012 length "1..max"; pattern "[^\*].*"; } description "Name of administrative group to which users can be assigned."; } typedef action-type { type enumeration { enum permit { description "Requested action is permitted."; } enum deny { description "Requested action is denied."; } } description "Action taken by the server when a particular rule matches."; } typedef node-instance-identifier { type yang:xpath1.0; description "Path expression used to represent a special data node instance identifier string. A node-instance-identifier value is an unrestricted YANG instance-identifier expression. All the same rules as an instance-identifier apply except predicates for keys are optional. If a key predicate is missing, then the node-instance-identifier represents all possible server instances for that key. This XPath expression is evaluated in the following context: o The set of namespace declarations are those in scope on the leaf element where this type is used. o The set of variable bindings contains one variable, 'USER', which contains the name of the user of the current session. o The function library is the core function library, but note that due to the syntax restrictions of an Bierman & Bjorklund Standards Track [Page 30]
RFC 6536 NACM March 2012 instance-identifier, no functions are allowed. o The context node is the root node in the data tree."; } /* * Data definition statements */ container nacm { nacm:default-deny-all; description "Parameters for NETCONF Access Control Model."; leaf enable-nacm { type boolean; default true; description "Enables or disables all NETCONF access control enforcement. If 'true', then enforcement is enabled. If 'false', then enforcement is disabled."; } leaf read-default { type action-type; default "permit"; description "Controls whether read access is granted if no appropriate rule is found for a particular read request."; } leaf write-default { type action-type; default "deny"; description "Controls whether create, update, or delete access is granted if no appropriate rule is found for a particular write request."; } leaf exec-default { type action-type; default "permit"; description "Controls whether exec access is granted if no appropriate Bierman & Bjorklund Standards Track [Page 31]
RFC 6536 NACM March 2012 rule is found for a particular protocol operation request."; } leaf enable-external-groups { type boolean; default true; description "Controls whether the server uses the groups reported by the NETCONF transport layer when it assigns the user to a set of NACM groups. If this leaf has the value 'false', any group names reported by the transport layer are ignored by the server."; } leaf denied-operations { type yang:zero-based-counter32; config false; mandatory true; description "Number of times since the server last restarted that a protocol operation request was denied."; } leaf denied-data-writes { type yang:zero-based-counter32; config false; mandatory true; description "Number of times since the server last restarted that a protocol operation request to alter a configuration datastore was denied."; } leaf denied-notifications { type yang:zero-based-counter32; config false; mandatory true; description "Number of times since the server last restarted that a notification was dropped for a subscription because access to the event type was denied."; } container groups { description "NETCONF Access Control Groups."; list group { Bierman & Bjorklund Standards Track [Page 32]
RFC 6536 NACM March 2012 key name; description "One NACM Group Entry. This list will only contain configured entries, not any entries learned from any transport protocols."; leaf name { type group-name-type; description "Group name associated with this entry."; } leaf-list user-name { type user-name-type; description "Each entry identifies the username of a member of the group associated with this entry."; } } } list rule-list { key "name"; ordered-by user; description "An ordered collection of access control rules."; leaf name { type string { length "1..max"; } description "Arbitrary name assigned to the rule-list."; } leaf-list group { type union { type matchall-string-type; type group-name-type; } description "List of administrative groups that will be assigned the associated access rights defined by the 'rule' list. The string '*' indicates that all groups apply to the entry."; Bierman & Bjorklund Standards Track [Page 33]
RFC 6536 NACM March 2012 } list rule { key "name"; ordered-by user; description "One access control rule. Rules are processed in user-defined order until a match is found. A rule matches if 'module-name', 'rule-type', and 'access-operations' match the request. If a rule matches, the 'action' leaf determines if access is granted or not."; leaf name { type string { length "1..max"; } description "Arbitrary name assigned to the rule."; } leaf module-name { type union { type matchall-string-type; type string; } default "*"; description "Name of the module associated with this rule. This leaf matches if it has the value '*' or if the object being accessed is defined in the module with the specified module name."; } choice rule-type { description "This choice matches if all leafs present in the rule match the request. If no leafs are present, the choice matches all requests."; case protocol-operation { leaf rpc-name { type union { type matchall-string-type; type string; } description "This leaf matches if it has the value '*' or if Bierman & Bjorklund Standards Track [Page 34]
RFC 6536 NACM March 2012 its value equals the requested protocol operation name."; } } case notification { leaf notification-name { type union { type matchall-string-type; type string; } description "This leaf matches if it has the value '*' or if its value equals the requested notification name."; } } case data-node { leaf path { type node-instance-identifier; mandatory true; description "Data Node Instance Identifier associated with the data node controlled by this rule. Configuration data or state data instance identifiers start with a top-level data node. A complete instance identifier is required for this type of path value. The special value '/' refers to all possible datastore contents."; } } } leaf access-operations { type union { type matchall-string-type; type access-operations-type; } default "*"; description "Access operations associated with this rule. This leaf matches if it has the value '*' or if the bit corresponding to the requested operation is set."; } leaf action { Bierman & Bjorklund Standards Track [Page 35]
RFC 6536 NACM March 2012 type action-type; mandatory true; description "The access control action associated with the rule. If a rule is determined to match a particular request, then this object is used to determine whether to permit or deny the request."; } leaf comment { type string; description "A textual description of the access rule."; } } } } } <CODE ENDS> 3.6. IANA Considerations This document registers one URI in "The IETF XML Registry". Following the format in [RFC3688], the following has been registered. URI: urn:ietf:params:xml:ns:yang:ietf-netconf-acm Registrant Contact: The IESG. XML: N/A, the requested URI is an XML namespace. This document registers one module in the "YANG Module Names" registry. Following the format in [RFC6020], the following has been registered. Name: ietf-netconf-acm Namespace: urn:ietf:params:xml:ns:yang:ietf-netconf-acm Prefix: nacm reference: RFC 6536 3.7. Security Considerations This entire document discusses access control requirements and mechanisms for restricting NETCONF protocol behavior within a given session. This section highlights the issues for an administrator to consider when configuring a NETCONF server with NACM. Bierman & Bjorklund Standards Track [Page 36]
RFC 6536 NACM March 2012 3.7.1. NACM Configuration and Monitoring Considerations Configuration of the access control system is highly sensitive to system security. A server may choose not to allow any user configuration to some portions of it, such as the global security level or the groups that allowed access to system resources. By default, NACM enforcement is enabled. By default, "read" access to all datastore contents is enabled (unless "nacm:default-deny-all" is specified for the data definition), and "exec" access is enabled for safe protocol operations. An administrator needs to ensure that NACM is enabled and also decide if the default access parameters are set appropriately. Make sure the following data nodes are properly configured: o /nacm/enable-nacm (default "true") o /nacm/read-default (default "permit") o /nacm/write-default (default "deny") o /nacm/exec-default (default "permit") An administrator needs to restrict write access to all configurable objects within this data model. If write access is allowed for configuration of access control rules, then care needs to be taken not to disrupt the access control enforcement. For example, if the NACM access control rules are edited directly within the running configuration datastore (i.e., :writable-running capability is supported and used), then care needs to be taken not to allow unintended access while the edits are being done. An administrator needs to make sure that the translation from a transport- or implementation-dependent user identity to a NACM username is unique and correct. This requirement is specified in detail in Section 2.2 of [RFC6241]. An administrator needs to be aware that the YANG data structures representing access control rules (/nacm/rule-list and /nacm/ rule-list/rule) are ordered by the client. The server will evaluate the access control rules according to their relative conceptual order within the running datastore configuration. Bierman & Bjorklund Standards Track [Page 37]
RFC 6536 NACM March 2012 Note that the /nacm/groups data structure contains the administrative group names used by the server. These group names may be configured locally and/or provided through an external protocol, such as RADIUS [RFC2865][RFC5607]. An administrator needs to be aware of the security properties of any external protocol used by the NETCONF transport layer to determine group names. For example, if this protocol does not protect against man-in-the-middle attacks, an attacker might be able to inject group names that are configured in NACM, so that a user gets more permissions than it should. In such cases, the administrator may wish to disable the usage of such group names, by setting /nacm/ enable-external-groups to "false". An administrator needs to restrict read access to the following objects within this data model, as they reveal access control configuration that could be considered sensitive. o /nacm/enable-nacm o /nacm/read-default o /nacm/write-default o /nacm/exec-default o /nacm/enable-external-groups o /nacm/groups o /nacm/rule-list 3.7.2. General Configuration Issues There is a risk that invocation of non-standard protocol operations will have undocumented side effects. An administrator needs to construct access control rules such that the configuration datastore is protected from such side effects. It is possible for a session with some write access (e.g., allowed to invoke <edit-config>), but without any access to a particular datastore subtree containing sensitive data, to determine the presence or non-presence of that data. This can be done by repeatedly issuing some sort of edit request (create, update, or delete) and possibly receiving "access-denied" errors in response. These "fishing" attacks can identify the presence or non-presence of specific sensitive data even without the "error-path" field being present within the <rpc-error> response. Bierman & Bjorklund Standards Track [Page 38]
RFC 6536 NACM March 2012 It may be possible for the set of NETCONF capabilities on the server to change over time. If so, then there is a risk that new protocol operations, notifications, and/or datastore content have been added to the device. An administrator needs to be sure the access control rules are correct for the new content in this case. Mechanisms to detect NETCONF capability changes on a specific device are outside the scope of this document. It is possible that the data model definition itself (e.g., YANG when-stmt) will help an unauthorized session determine the presence or even value of sensitive data nodes by examining the presence and values of different data nodes. There is a risk that non-standard protocol operations, or even the standard <get> protocol operation, may return data that "aliases" or "copies" sensitive data from a different data object. There may simply be multiple data model definitions that expose or even configure the same underlying system instrumentation. A data model may contain external keys (e.g., YANG leafref), which expose values from a different data structure. An administrator needs to be aware of sensitive data models that contain leafref nodes. This entails finding all the leafref objects that "point" at the sensitive data (i.e., "path-stmt" values) that implicitly or explicitly include the sensitive data node. It is beyond the scope of this document to define access control enforcement procedures for underlying device instrumentation that may exist to support the NETCONF server operation. An administrator can identify each protocol operation that the server provides and decide if it needs any access control applied to it. This document incorporates the optional use of a recovery session mechanism, which can be used to bypass access control enforcement in emergencies, such as NACM configuration errors that disable all access to the server. The configuration and identification of such a recovery session mechanism are implementation-specific and outside the scope of this document. An administrator needs to be aware of any recovery session mechanisms available on the device and make sure they are used appropriately. It is possible for a session to disrupt configuration management, even without any write access to the configuration, by locking the datastore. This may be done to ensure all or part of the configuration remains stable while it is being retrieved, or it may be done as a "denial-of-service" attack. There is no way for the server to know the difference. An administrator may wish to restrict "exec" access to the following protocol operations: Bierman & Bjorklund Standards Track [Page 39]
RFC 6536 NACM March 2012 o <lock> o <unlock> o <partial-lock> o <partial-unlock> 3.7.3. Data Model Design Considerations Designers need to clearly identify any sensitive data, notifications, or protocol operations defined within a YANG module. For such definitions, a "nacm:default-deny-write" or "nacm:default-deny-all" statement ought to be present, in addition to a clear description of the security risks. Protocol operations need to be properly documented by the data model designer, so it is clear to administrators what data nodes (if any) are affected by the protocol operation and what information (if any) is returned in the <rpc-reply> message. Data models ought to be designed so that different access levels for input parameters to protocol operations are not required. Use of generic protocol operations should be avoided, and if different access levels are needed, separate protocol operations should be defined instead. 4. References 4.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, January 2004. [RFC5277] Chisholm, S. and H. Trevino, "NETCONF Event Notifications", RFC 5277, July 2008. [RFC6020] Bjorklund, M., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, October 2010. [RFC6021] Schoenwaelder, J., "Common YANG Data Types", RFC 6021, October 2010. Bierman & Bjorklund Standards Track [Page 40]
RFC 6536 NACM March 2012 [RFC6241] Enns, R., Bjorklund, M., Schoenwaelder, J., and A. Bierman, "Network Configuration Protocol (NETCONF)", RFC 6241, June 2011. 4.2. Informative References [RFC2865] Rigney, C., Willens, S., Rubens, A., and W. Simpson, "Remote Authentication Dial In User Service (RADIUS)", RFC 2865, June 2000. [RFC5607] Nelson, D. and G. Weber, "Remote Authentication Dial-In User Service (RADIUS) Authorization for Network Access Server (NAS) Management", RFC 5607, July 2009. Bierman & Bjorklund Standards Track [Page 41]
RFC 6536 NACM March 2012 Appendix A. Usage Examples The following XML snippets are provided as examples only, to demonstrate how NACM can be configured to perform some access control tasks. A.1. <groups> Example There needs to be at least one <group> entry in order for any of the access control rules to be useful. The following XML shows arbitrary groups and is not intended to represent any particular use case. <nacm xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-acm"> <groups> <group> <name>admin</name> <user-name>admin</user-name> <user-name>andy</user-name> </group> <group> <name>limited</name> <user-name>wilma</user-name> <user-name>bam-bam</user-name> </group> <group> <name>guest</name> <user-name>guest</user-name> <user-name>guest@example.com</user-name> </group> </groups> </nacm> This example shows three groups: admin: The "admin" group contains two users named "admin" and "andy". limited: The "limited" group contains two users named "wilma" and "bam-bam". guest: The "guest" group contains two users named "guest" and "guest@example.com". Bierman & Bjorklund Standards Track [Page 42]
RFC 6536 NACM March 2012 A.2. Module Rule Example Module rules are used to control access to all the content defined in a specific module. A module rule has the <module-name> leaf set, but no case in the "rule-type" choice. <nacm xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-acm"> <rule-list> <name>guest-acl</name> <group>guest</group> <rule> <name>deny-ncm</name> <module-name>ietf-netconf-monitoring</module-name> <access-operations>*</access-operations> <action>deny</action> <comment> Do not allow guests any access to the NETCONF monitoring information. </comment> </rule> </rule-list> <rule-list> <name>limited-acl</name> <group>limited</group> <rule> <name>permit-ncm</name> <module-name>ietf-netconf-monitoring</module-name> <access-operations>read</access-operations> <action>permit</action> <comment> Allow read access to the NETCONF monitoring information. </comment> </rule> <rule> <name>permit-exec</name> <module-name>*</module-name> <access-operations>exec</access-operations> <action>permit</action> <comment> Allow invocation of the supported server operations. </comment> </rule> </rule-list> Bierman & Bjorklund Standards Track [Page 43]
RFC 6536 NACM March 2012 <rule-list> <name>admin-acl</name> <group>admin</group> <rule> <name>permit-all</name> <module-name>*</module-name> <access-operations>*</access-operations> <action>permit</action> <comment> Allow the admin group complete access to all operations and data. </comment> </rule> </rule-list> </nacm> This example shows four module rules: deny-ncm: This rule prevents the "guest" group from reading any monitoring information in the "ietf-netconf-monitoring" YANG module. permit-ncm: This rule allows the "limited" group to read the "ietf- netconf-monitoring" YANG module. permit-exec: This rule allows the "limited" group to invoke any protocol operation supported by the server. permit-all: This rule allows the "admin" group complete access to all content in the server. No subsequent rule will match for the "admin" group because of this module rule. A.3. Protocol Operation Rule Example Protocol operation rules are used to control access to a specific protocol operation. <nacm xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-acm"> <rule-list> <name>guest-limited-acl</name> <group>limited</group> <group>guest</group> <rule> <name>deny-kill-session</name> <module-name>ietf-netconf</module-name> <rpc-name>kill-session</rpc-name> Bierman & Bjorklund Standards Track [Page 44]
RFC 6536 NACM March 2012 <access-operations>exec</access-operations> <action>deny</action> <comment> Do not allow the limited or guest group to kill another session. </comment> </rule> <rule> <name>deny-delete-config</name> <module-name>ietf-netconf</module-name> <rpc-name>delete-config</rpc-name> <access-operations>exec</access-operations> <action>deny</action> <comment> Do not allow limited or guest group to delete any configurations. </comment> </rule> </rule-list> <rule-list> <name>limited-acl</name> <group>limited</group> <rule> <name>permit-edit-config</name> <module-name>ietf-netconf</module-name> <rpc-name>edit-config</rpc-name> <access-operations>exec</access-operations> <action>permit</action> <comment> Allow the limited group to edit the configuration. </comment> </rule> </rule-list> </nacm> This example shows three protocol operation rules: deny-kill-session: This rule prevents the "limited" or "guest" groups from invoking the NETCONF <kill-session> protocol operation. deny-delete-config: This rule prevents the "limited" or "guest" groups from invoking the NETCONF <delete-config> protocol operation. Bierman & Bjorklund Standards Track [Page 45]
RFC 6536 NACM March 2012 permit-edit-config: This rule allows the "limited" group to invoke the NETCONF <edit-config> protocol operation. This rule will have no real effect unless the "exec-default" leaf is set to "deny". A.4. Data Node Rule Example Data node rules are used to control access to specific (config and non-config) data nodes within the NETCONF content provided by the server. <nacm xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-acm"> <rule-list> <name>guest-acl</name> <group>guest</group> <rule> <name>deny-nacm</name> <path xmlns:n="urn:ietf:params:xml:ns:yang:ietf-netconf-acm"> /n:nacm </path> <access-operations>*</access-operations> <action>deny</action> <comment> Deny the guest group any access to the /nacm data. </comment> </rule> </rule-list> <rule-list> <name>limited-acl</name> <group>limited</group> <rule> <name>permit-acme-config</name> <path xmlns:acme="http://example.com/ns/netconf"> /acme:acme-netconf/acme:config-parameters </path> <access-operations> read create update delete </access-operations> <action>permit</action> <comment> Allow the limited group complete access to the acme NETCONF configuration parameters. Showing long form of 'access-operations' instead of shorthand. </comment> </rule> </rule-list> Bierman & Bjorklund Standards Track [Page 46]
RFC 6536 NACM March 2012 <rule-list> <name>guest-limited-acl</name> <group>guest</group> <group>limited</group> <rule> <name>permit-dummy-interface</name> <path xmlns:acme="http://example.com/ns/itf"> /acme:interfaces/acme:interface[acme:name='dummy'] </path> <access-operations>read update</access-operations> <action>permit</action> <comment> Allow the limited and guest groups read and update access to the dummy interface. </comment> </rule> </rule-list> <rule-list> <name>admin-acl</name> <group>admin</group> <rule> <name>permit-interface</name> <path xmlns:acme="http://example.com/ns/itf"> /acme:interfaces/acme:interface </path> <access-operations>*</access-operations> <action>permit</action> <comment> Allow admin full access to all acme interfaces. </comment> </rule> </rule-list> </nacm> This example shows four data node rules: deny-nacm: This rule denies the "guest" group any access to the <nacm> subtree. Note that the default namespace is only applicable because this subtree is defined in the same namespace as the <data-rule> element. permit-acme-config: This rule gives the "limited" group read-write access to the acme <config-parameters>. Bierman & Bjorklund Standards Track [Page 47]
RFC 6536 NACM March 2012 permit-dummy-interface: This rule gives the "limited" and "guest" groups read-update access to the acme <interface> entry named "dummy". This entry cannot be created or deleted by these groups, just altered. permit-interface: This rule gives the "admin" group read-write access to all acme <interface> entries. A.5. Notification Rule Example Notification rules are used to control access to a specific notification event type. <nacm xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-acm"> <rule-list> <name>sys-acl</name> <group>limited</group> <group>guest</group> <rule> <name>deny-config-change</name> <module-name>acme-system</module-name> <notification-name>sys-config-change</notification-name> <access-operations>read</access-operations> <action>deny</action> <comment> Do not allow the guest or limited groups to receive config change events. </comment> </rule> </rule-list> </nacm> This example shows one notification rule: deny-config-change: This rule prevents the "limited" or "guest" groups from receiving the acme <sys-config-change> event type. Bierman & Bjorklund Standards Track [Page 48]
RFC 6536 NACM March 2012 Authors' Addresses Andy Bierman YumaWorks EMail: andy@yumaworks.com Martin Bjorklund Tail-f Systems EMail: mbj@tail-f.com Bierman & Bjorklund Standards Track [Page 49]